Operating Instructions - VEGAPULS 54K enamel

More documents

Recommendations

Info

5 Diagnostics 5.1 Simulation To simulate a certain filling level, you can call up the function “Simulation” in the adjustment module MINICOM, in the adjustment software PACTware TM or in the HART ® handheld. You simulate a vessel filling and thereby a certain sensor current. Please note that connected instruments, such as e.g. a PLC, react according to their settings and will probably activate alarms or system functions. One hour after the last simulation adjustment, the sensor returns automatically to standard operating mode. 5.2 Error codes Display Meaning Rectifying measure Diagnostics E013 No valid measured value Message is displayed during warm-up phase - Sensor in the warm-up phase - Loss of the useful echo If the message remains, a false echo storage must be made with the adjustment module MINICOM in the menu “sensor optimisation” or better, with the PC and VVO. If the message still remains, carry out a fresh adjustment. E017 Adjustment span too small Carry out a readjustment. Make sure that the difference between min. and max. adjustment is at least 10 mm. E036 Sensor software does not - Sensor must be programmed with new run software (service) - Message appears during a software update. E040 Hardware failure/Electronics Check all connection cables. defective Contact our service department. 38 VEGAPULS 54K enamel 24 101-EN-041227
24 101-EN-041227 Technical data 6 Technical data 6.1 Technical data Power supply Power supply - four-wire sensor 24 V DC (20 … 72 V DC) 230 V AC (20 … 250 V AC), 50/60 Hz fuse 0.2 A TR - two-wire sensor 24 V DC (14 … 36 V DC) - two-wire Ex ia sensor 24 V DC (14 … 29 V DC) - two-wire Ex d ia sensor 24 V DC (20 … 36 V DC) Current consumption - four-wire sensor max. 60 mA - two-wire sensor max. 22.5 mA Power consumption - four-wire sensor max. 200 mW, 1.2 VA - two-wire sensor 55 … 810 mW Load - four-wire sensors max. 500 Ohm - two-wire sensors see load diagram Ω 1000 975 900 800 720 700 670 600 500 400 max. load Ex ia max. load non-Ex max. load Ex d ia Non-Ex and Ex ia max. voltage limit non-Ex and Ex d ia sensors max. Spannungsgrenze Ex ia-Sensoren 300 250 200 Load resistance (HART 100 0 15 19,5 25,5 29 36 14 20 25 30 35 ® min. voltage limit when using the HART and VEGACONNECT) ® adjustment resistance: - non-Ex and Ex ia sensors - Ex d ia sensors Exd ia VEGAPULS 54K enamel 39 V
Page 1 and 2: Operating Instructions VEGAPULS 54K
Page 3 and 4: 24 101-EN-041227 Sicherheitshinweis
Page 5 and 6: 24 101-EN-041227 Product descriptio
Page 7 and 8: 24 101-EN-041227 Product descriptio
Page 9 and 10: 24 101-EN-041227 Mounting and insta
Page 15 and 16: 24 101-EN-041227 Electrical connect
Page 29 and 30: 24 101-EN-041227 Set-up Rx 250 Ω
Page 31 and 32: 24 101-EN-041227 Set-up 2. Operatin
Page 33 and 34: 24 101-EN-041227 Set-up Confirm wit
Page 35 and 36: 24 101-EN-041227 Set-up False echo
Page 37: 24 101-EN-041227 Set-up Rx VEGAMET
Page 41 and 42: 24 101-EN-041227 Technical data Mea
Page 43 and 44: 24 101-EN-041227 Technical data 6.2
Page 45 and 46: 24 101-EN-041227 Technical data VEG
Page 47 and 48: 24 101-EN-041227 Supplement 1.4 Det
Page 49 and 50: 24 101-EN-041227 Supplement 3 Set-u
Page 51 and 52: 24 101-EN-041227 Supplement 6 Safet
Page 53 and 54: 24 101-EN-041227 Supplement CE decl
Page 55 and 56: 24 101-EN-041227 Supplement VEGAPUL

Operating Instructions - VEGAPULS 54K enamel

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?