CAD user manual - Finn-Power International, Inc.

More documents

Recommendations

Info

Extend Line to Limits- Extend a line to the set boundary. Angle to line- Draw a construction line at an angle at a given point on the selected element. Bisector of 2 lines- Draw a construction bisector at an angle. 2.2 Arcs Note that the radius is positive in all cases. Where there is ambiguity the system will display all the possible solutions one at a time You can cycle through the solutions. Click OK when you have the one you want. Cancel rejects all solutions 3 Point Arc- Arc defined by 3 points. Semicircle- Semicircle defined by 2 points. NOTE-there are 2 possible solutions. Arc Centre 2 Points- Arc specified by centre and then 2 points. NOTE- there are 2 possible solutions. Arc 2 Point Radius- Arc specified by 2 points and radius. NOTE- there are 4 possible solutions. Arc Centre Radius 2 Angles- Arc specified centre radius and 2 angles. NOTE- there are 2 possible solutions. Arc Centre Start Point Subangle- Arc specified by centre, Start Point and then Subtended angle. NOTE- clockwise angles are negative, counter clockwise are positive. 10
Arc Point Radius Subangle- Arc Specified by Start Point, Start Angle, Radius and then Subtended angle. Parallel Element – Distance- Parallel arc at a given distance. Touch the required side and input the distance. If on the inside the distance must be less than the radius. Parallel Element – Point- Parallel arc through a given point. 2.3 Circles Circle Centre Diameter- Circle specified by defining the centre point and then diameter. Circle 2 Points- Circle specified by two points on the diameter. Circle 3 Points- Circle specified by three points. Circle Centre Point- Circle specified by centre point and point on circumference (diameter). Circle 2 Points and Radius- Circle specified by two points on the circumference and radius. NOTE- there are two possible solutions. Tangent to 1 Element (2 Points)- Circle through two points tangential to a line. Tangent to 1 Element, Point and Radius- Circle specified through a point with a given radius, and tangential to a line or arc. NOTE- there may be two solutions. Tangent to 1 Element Centre- Circle with a given centre tangential to an arc or a line. Circle Tangent 2 Elements- Circle tangential to two elements with given radius. NOTE- there may be two solutions. (same as ) 11
Page 1 and 2: Finn-Power International 710 Reming
Page 3 and 4: INTRODUCTION ______________________
Page 5 and 6: 1 GETTING AROUND It is obvious the
Page 7 and 8: Delete Construction Lines Construct
Page 9: 2 CAD FUNCTIONS As described earlie
Page 13 and 14: Rectangular Notch- Input width and
Page 15 and 16: 2.8 Copy When using the Copy functi
Page 17 and 18: 2.10 Modify Commands Undo- Undo the
Page 19 and 20: HOW TO USE- Select Line 2 Point, fo
Page 21 and 22: TANGENT- Used to draw geometry tang
Page 23 and 24: 270°) throughout the circular shap
Page 25 and 26: part. Although there are many diffe
Page 27 and 28: STEP 6: Chose Absolute again from t
Page 29 and 30: Now create a second rectangle in th
Page 31 and 32: 4.2 Exercise 2 We will start with t
Page 33 and 34: The next steps will add two rectang
Page 35 and 36: The next steps will add obround slo
Page 37 and 38: on the toolbar to allow selection o
Page 39 and 40: There are two operations left to ap
Page 41 and 42: 4.3 Exercise 3 For this part the 0,
Page 43 and 44: STEP 13: Choose End Point from the
Page 45 and 46: STEP 25: NC Express will now ask fo
Page 47 and 48: This means that we can draw more th
Page 49: 5 Appendix Below is a shortcut key

CAD user manual - Finn-Power International, Inc.

Create successful ePaper yourself

Delete template?

Save as template?