HAHN+KOLB-Toolcatalog 2011/12 – Metal Cutting Tools

Metal-cutting tools
Milling tools
Cutters with indexable inserts
Continued next page
Heavy-duty face milling head 45°
Shorter production times call for a high degree of precision from the tools being used and for high process
reliability. Conventional tools cannot always assure this. The heavy-duty face milling head is a tool for the
cost-effective machining of steel and cast materials. The indexable insert can be used on both sides and
has a total of 16 cutting edges. The cutting edges make considerable higher feed rates possible despite the
lower axial delivery values of max. 3 mm (4 mm) – for an insert size of 12.7 mm (16 mm) and in this way
contribute significantly to the productivity increases. Because the axial forces are low, the largest possible
flatness of the machined surfaces is assured for low surface roughness values (Rz < 15 μm), even for
roughing operations.
Advantages:
•indexable insert with 16 cutting edges (eight cutting edges on each side)
•indexable insert for use both as a roughing and a finishing insert
•high tooth feed and feed rates are possible
•high economic efficiency from the many cutting edges
Continued next page
Heavy-duty face milling head 45°
for indexable inserts ONG. O..
45°
ONGU
05 . .
ONGU
06 . .
Box qty.: No. 16108 = 10 pieces
Z
3-19
Nominal Ø
Sizes
Milling head
without indexable inserts
Clamping screw for inserts
d
D
D d ap max L1 z Indexable inserts 16002 M 16108
mm mm mm mm Type Ident. No. U. pr. E mm Ident. No. U. pr. E
32 16
3
200 (O. R.)
32 16 4 202 (O. R.)
40 22 4 204 O. R.
40 22 5 206 O. R.
50 22
3 40
5
40
208 O. R.
4X9 085 O. R.
50 22 7 210 O. R.
63 22 7 212 O. R.
63 22 9 214 O. R.
50 22
40 4
216 O. R.
50 22 40 6 218 O. R.
63 22 40 5 220 O. R.
63 22 40 8 222 O. R.
80 27 50 7 224 O. R.
80 27 50 10 226 O. R.
100 32
4
50 9
41
228 O. R.
4X10 086 O. R.
100 32 50 12 230 O. R.
125 40 63 11 232 O. R.
125 40 63 15 234 O. R.
160 40 63 13 236 (O. R.)
160 40 63 19 238 (O. R.)
-5°
-5°
L1
15°
45° 1)
3 8
WPL ONGU0505
15°
45° 1)
4 10
WPL ONGU0606
1)
exactly 44° 30'
h Screw driver for WSP clamping screw:
No. 52143 915 page 1174 = No. 16108 085; No. 52143 920 page 1174 = No. 16108
086.
No. 52143 920 page 1174 fitting for clamping screws No. 16108 086.
Indexable inserts type 40 and 41 for holder: No. 16109 680-694 = page 257.
No. 16002 = Prod. Gr. 108
No. 16108 = Prod. Gr. 106
256 2011/12