HAHN+KOLB-Toolcatalog 2011/12 – Metal Cutting Tools

Metal-cutting tools
Lathe tools
KOMET insert holders
Continued next page
Carbide-tipped indexable inserts TOHX ...
LH cutter geometry, with 3 ground cutters
Application: inside turning.
Execution: with chip breaker.
Box qty.: 10 units.
coated uncoated uncoated
Application steel cast, non-ferrous steel
Material group
Carbide types
BK
(= ..60)
K 10
(= ..21)
P 25 M
(= ..03)
Cut w Carbide indexable inserts Sizes
γ Type M s r 17766 17766 17766
6°
mm mm mm Ident. No. U. pr. E Ident. No. U. pr. E Ident. No. U. pr. E
W30 04060.03.. 1,8 3,5 0,3 516 O. R. 519 O. R. 513 O. R.
W30 14060.04.. 2,5 4,5 0,4 616 O. R. 619 O. R. 613 O. R.
W30 26060.05.. 3,0 6,0 0,5 716 O. R. – – 713 O. R.
W30 04120.03.. 1,8 3,5 0,3 536 O. R. – – 533 O. R.
12° W30 14120.04.. 2,5 4,5 0,4 636 O. R. – – 633 O. R.
W30 26120.05.. 3,0 6,0 0,5 – – 739 O. R. 733 O. R.
20° W30 04200.03.. 1,8 3,5 0,3 – – 559 O. R. – –
h Suitable boring bar No. 17807 page 402.
i Selection aid carbide-tipped indexable inserts page 398.
Prod. Gr. 173
Continued next page
Clamping holder for indexable inserts
type SWLC R / SWGC R / PM / APM
h On request.
Type PM
Type APM
Continued next page
Ultra-small boring bars with indexable inserts
Type UJ 92° / B 00
Application: for inside machining of bore holes from Ø 7.9 mm for through and blind holes, for indexable
insert type W30
See carbide indexable inserts No. 17766 page 402 (left hand insert to the right hand holder)
*Relieving with coolant delivery through central coolant delivery.
RH cutter geometry
Note: clamping screws are continuously changed from Torx to TorxPlus. Therefore, it is possible that still
Torx screws are delivered.
Boring bars
Clamping screws
Packed set = quantity 10
Boring bars Boring bars To
Type Sizes Indexable inserts
D min. d I1 Useful length l2 f α No. 17766 17807 Size 17769
mm mm mm mm mm Type Ident. No. U. pr. E Ident. No. U. pr. E
UJ 8 7,9 8 85 15 3,95 8°30´ W30 04... 008 O. R.
UJ 10 9,9 10 95 20 4,95 5°30´ W30 04... 010 O. R.
M 2 x 2,8 - 6IP 101 O. R.
UJ 12 11,9 12 110 25 5,95 7°30´ W30 14... 012 O. R.
UJ 15 14,9 15 120 30 7,45 5° W30 14... 015 O. R.
UJ 16 15,9 16 120 30 7,95 5° W30 14... 016 O. R.
UJ 18 17,9 18 150 40 8,95 5°30´ W30 26... 018 O. R.
UJ 20 19,9 20 150 40 9,95 4°30´ W30 26... 020 O. R.
M 2,6 x 4 - 8IP 106 O. R.
M 3,5 x 6 - 10IP 109 O. R.
h Screwdriver:
No. 52143 106 page 1175 to fit clamping screws No. 17769 101.
No. 52143 108 page 1175 to fit clamping screws No. 17769 106.
No. 52143 110 page 1175 to fit clamping screws No. 17769 109.
Prod. Gr. 172
402 2011/12