string

More documents

Recommendations

Info

Action If print jobs are coming out of the printer in question, wait until they are finished and then resubmit this print job. If you see this message again, the lp(1) system is probably hung. See the message "lp hang" for a procedure to clear the queue. Technical Notes If lp(1) is unable to create a device for printer messages, the message FIFO could be already in use, or locked by another print job. See Also For more information on the print scheduler, see the section on administrating printers in the System Administration Guide Volume II. Can’t invoke /etc/init, error int Cause This message can appear while a system is booting, indicating that the init(1M) program is missing or corrupted. Note that /etc/init is a symbolic link to /sbin/init. Action Boot the miniroot so you can replace init(1M). Halt the machine by typing Stop-A or by pressing the reset button. Reboot single-user from CD-ROM, the net, or diskette. For example, type boot cdrom -s at the ok prompt to boot from CD-ROM. After the system comes up and gives you a # prompt, mount the device corresponding to the original / partition somewhere, with a command similar to the mount(1M) command below. Then copy the init(1M) program from the miniroot to the original / partition, and reboot the system. # mount /dev/dsk/c0t3d0s0 /mnt # cp /sbin/init /mnt/sbin/init # reboot 34 Solaris Common Messages and Troubleshooting Guide ♦ October, 1998
If this doesn’t work, other files might be corrupted, and you might need to reinstall the entire system. Technical Notes The error number is 2 if /sbin/init is missing, or 8 if /sbin/init has an incorrect executable format. This is usually followed by a "panic: icode" message. The system tries to reboot itself, but goes into a loop, because rebooting is impossible without init(1M). See Also For more information on booting the system, see the section on halting and booting the system in the System Administration Guide, Volume I. can’t open /dev/rdsk/<strong>string</strong>: (null): UNEXPECTED INCONSISTENCY Cause On SunOS 4.1.x, this message indicated that the device containing the /dev filesystem has become disconnected. Solaris behavior has not been confirmed. can’t synchronize with hayes Cause This message sometimes appears when using a modem that the system regards as a "Hayes" type modem, which includes most modems manufactured today. The message can be caused by incorrect switch settings, by poor cable connections, or by not turning the modem on. Action Check that the modem is on and that the cables between the modem and your system are securely connected. Check the internal and external modem switch settings. Turn the modem off and then on again, if necessary. Alphabetical Message Listing 35
Page 1 and 2:
Solaris Common Messages and Trouble
Page 3 and 4:
Contents Preface xxi 1. About Error
Page 5 and 6:
"C" 30 bad module/chip at: position
Page 7 and 8: "E" 58 Device busy 50 device busy 5
Page 9 and 10: "H" 77 "I" 80 giving up 76 Graphics
Page 11 and 12: le0: No carrier-- cable disconnecte
Page 13 and 14: Network is down 120 Network is unre
Page 15 and 16: Operation not applicable 147 "P" 15
Page 17 and 18: Slice c0t1d0s0 is too small to cont
Page 19 and 20: user unknown 195 /usr/dt/bin/rpc.tt
Page 21 and 22: Preface System administrators and a
Page 23: TABLE P-1 Typographic Conventions (
Page 26 and 27: Variable words and numbers can appe
Page 28 and 29: TABLE 1-2 AnswerBook Search Results
Page 30 and 31: 6 Solaris Common Messages and Troub
Page 32 and 33: ** Phase 1-- Check Blocks and Sizes
Page 34 and 35: ** Phase 4-- Check Reference Counts
Page 36 and 37: 451 timeout waiting for input durin
Page 38 and 39: Action Check the value of the $j ma
Page 40 and 41: Address already in use Cause User a
Page 42 and 43: Arg list too long Cause The system
Page 44 and 45: Attempting to link in more shared l
Page 46 and 47: BAD/DUP FILE I=i OWNER=o MODE=m SIZ
Page 48 and 49: Action Replace the memory module or
Page 50 and 51: BAD TRAP Cause A bad trap can indic
Page 52 and 53: oot error 13 | sun4m Cause Diskless
Page 54 and 55: "C" Cannot access a needed shared l
Page 56 and 57: Cannot find SERVER hostname in netw
Page 60 and 61: cd: Too many arguments Cause The C
Page 62 and 63: Communication error on send Cause T
Page 64 and 65: Technical Notes The symbolic name f
Page 66 and 67: Technical Notes Some signals, such
Page 68 and 69: Could not initialize tooltalk (tt_o
Page 70 and 71: cpio : can’t read input : end of
Page 72 and 73: ¤ See the message "BAD TRAP" for m
Page 74 and 75: dev/rdsk/c0t6d0s2: No such file or
Page 76 and 77: # ./volmgt stop # ps -ef | grep vol
Page 78 and 79: Action To remove the directory, fir
Page 80 and 81: # ls -lL /dev/rdsk/c2t0d0s1 crw----
Page 82 and 83: See Also For more information, see
Page 84 and 85: Error 76 Cause This error is RFS sp
Page 86 and 87: Error Host Unknown: Cause On Window
Page 88 and 89: Action Run vxserial -p to print the
Page 90 and 91: Exec format error Cause This often
Page 92 and 93: fd0: unformatted diskette or no dis
Page 94 and 95: Action Have the original owner chan
Page 96 and 97: Action Simply waiting often gives t
Page 98 and 99: ftp: ftp/tcp: unknown service Cause
Page 100 and 101: "G" giving up Cause This message ap
Page 102 and 103: home/string: No such file or direct
Page 104 and 105: "I" I can’t read your attachments
Page 106 and 107: ifconfig: bad address Cause System
Page 108 and 109:
Technical Notes Sometimes this cond
Page 110 and 111:
INCORRECT BLOCK COUNT I=int (should
Page 112 and 113:
inetd[int]: string/udp: unknown ser
Page 114 and 115:
Interrupted system call Cause The u
Page 116 and 117:
I/O error Cause Some physical Input
Page 118 and 119:
"K" kernel read error Cause This me
Page 120 and 121:
ld.so.1 fatal: can’t set protecti
Page 122 and 123:
Technical Notes This error does not
Page 124 and 125:
When a machine is configured as a n
Page 126 and 127:
Link has been severed Cause This er
Page 128 and 129:
If you cannot log in to the system
Page 130 and 131:
mailtool: Could not initialize the
Page 132 and 133:
mailtool: Can’t create dead lette
Page 134 and 135:
file name may contain holes - can
Page 136 and 137:
mount: /dev/dsk/string is already m
Page 138 and 139:
Multihop attempted Cause This error
Page 140 and 141:
Action Run /etc/mount to see if the
Page 142 and 143:
"N" Name not unique on network Caus
Page 144 and 145:
Network dropped connection because
Page 146 and 147:
nfs mount: Couldn’t bind to reser
Page 148 and 149:
NFS read failed for server string C
Page 150 and 151:
NFS string failed for server string
Page 152 and 153:
NIS+ authentication failure Cause T
Page 154 and 155:
Technical Notes A wait(2) system ca
Page 156 and 157:
No recipients specified Cause This
Page 158 and 159:
filesystem and create symbolic link
Page 160 and 161:
Action Make sure the NIS map name i
Page 162 and 163:
Not a stream device Cause A putmsg(
Page 164 and 165:
(Continuation) (ssd22): Error for C
Page 166 and 167:
Not on system console Cause A user
Page 168 and 169:
6/04/98 7:27:54 nsrck: SYSTEM error
Page 170 and 171:
Operation already in progress Cause
Page 172 and 173:
Operation now in progress Cause An
Page 174 and 175:
Action Change the names of these vo
Page 176 and 177:
change all of these entries to file
Page 178 and 179:
See Also For more information, see
Page 180 and 181:
Permission denied Cause An attempt
Page 182 and 183:
Protocol not supported Cause The re
Page 184 and 185:
Read-only file system Cause Files a
Page 186 and 187:
To increase the size of the process
Page 188 and 189:
mdir: string: Directory not empty C
Page 190 and 191:
"S" save: SYSTEM error, Arg list to
Page 192 and 193:
Security exception on host string.
Page 194 and 195:
sendmail[int]: NOQUEUE: SYSERR: net
Page 196 and 197:
Your attempt to attach metastate da
Page 198 and 199:
Srmount error Cause This error is R
Page 200 and 201:
Technical Notes The rcp(1) and rsh(
Page 202 and 203:
su: ’su root’ succeeded for str
Page 204 and 205:
system hang Cause 4.1.3C SBUS cards
Page 206 and 207:
Text file busy Cause This can occur
Page 208 and 209:
See Also For more information, see
Page 210 and 211:
Action If you choose "Save Changes,
Page 212 and 213:
Action You can control the soft lim
Page 214 and 215:
6. The boot block is probably bad t
Page 216 and 217:
Unable to install/attach driver ’
Page 218 and 219:
Action Correct the command line and
Page 220 and 221:
usr/openwin/bin/xinit: connection t
Page 222 and 223:
"V" Value too large for defined dat
Page 224 and 225:
Action Check the date on the system
Page 226 and 227:
WARNING: No network locking on stri
Page 228 and 229:
WARNING: Unable to repair the / fil
Page 230 and 231:
Action On some system architectures
Page 232 and 233:
tried to run on the X server specif
Page 234 and 235:
XView warning: Cannot load font set
Page 236 and 237:
the ypwhich(1) command. When the se
show all

string

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?