EFM User Manual - CTC Union Technologies Co.,Ltd.

More documents

Recommendations

Info

3.8.5 Restart To restart (soft reset) the EFM modem, press Restart . When you press Restart, display screen is as following: Shown is the configuration successful save message. When the system has rebooted, you can re-open the browser. 66
4 Configuration use Serial Console and Telnet with Menu Driven Interface 4.1 Introduction 4.1.1 Login to the Console Interface The console port is a RJ-45 connector that enables a connection to a PC for monitoring and configuring the EFM modem. Use the supplied serial cable with a female DB-9 connector to serial port of PC and RJ-45 module jack connector to EFM modem’s console port. Start your terminal access program by terminal emulation program or Hyper Terminal and configure its communication parameters to match the following default characteristics of the console port: Parameter Value Baud rate 9600 Data Bits 8 Parity Check None Stop Bits 1 Flow-control None After finishing the parameter settings, press the SPACE key until the login screen appears. When you see the login screen, you can logon to this EFM Modem. Note: Only SPACE key invoke the login prompt. Pressing other keys will not work. The system asks for User and Password, please enter "admin" both for the factory default username and password. User: admin Password: ***** 4.1.2 Telnet login The EFM modem also supports Telnet protocol for remote management. Make sure the correct Ethernet cable is connected the MGMT port of EFM modem to your computer. The MGMT indicator on the front panel shall light if a correct cable is used. Start your Telnet client with VT100 terminal emulation and connecting to the management IP of EFM modem, wait for the login prompt to appear. Input User and Password after login screen pop up. The system asks for User and Password, please enter "admin" for both username and password. 67
Page 1:
G.SHDSL.bis EFM Network Extender
Page 4 and 5:
Legal The information in this publi
Page 6 and 7:
3.5.2 VLAN.........................
Page 8 and 9:
4.10 ADMINISTRATION................
Page 10 and 11:
1.2 Features Extend Ether
Page 12 and 13:
1.4 Applications EFM DSLAM to point
Page 14 and 15:
LED status of EFM Modem : LEDs Acti
Page 16 and 17: 2.2.2 LAN ports and MGMT port The E
Page 18 and 19: 3 Configuration use Web Browser 3.1
Page 20 and 21: 3.3 Setup up with Web Browser This
Page 22 and 23: The diagram below shows the basic s
Page 24 and 25: 3.4.2 DHCP server Press Next to set
Page 26 and 27: 3.4.3 LAN Press Next to set the nex
Page 28 and 29: 3.5 Advanced Setup Note: The advanc
Page 30 and 31: 3.5.1.5 SNR margin SNR margin is an
Page 33 and 34: 3.5.2.1 802.1Q Tag-Based VLAN Click
Page 35 and 36: Before enabling VLANs for the EFM m
Page 37 and 38: The default setting is all ports co
Page 39 and 40: On devices of different vendors, th
Page 41 and 42: 3.5.3.1 Port Based Priority When yo
Page 43 and 44: 3.5.3.2 VLAN Tag Priority When you
Page 45 and 46: According to the previous two table
Page 47 and 48: The following is an illustration ab
Page 49 and 50: 3.5.4 Rate Control Click Rate Contr
Page 51 and 52: The below display screen is from a
Page 53 and 54: 3.6.3 LAN LAN status will display t
Page 55 and 56: 3.7 Administration This session int
Page 57 and 58: Legal address pool will setup the l
Page 59 and 60: 3.7.2.1 Community Pool To enable th
Page 61 and 62: 3.8 Utility This section will descr
Page 63 and 64: 3.8.2 Config Tool The configuration
Page 65: 3.8.4 Logout To exit the web config
Page 69 and 70: The following figure gives you an e
Page 71 and 72: If you are the authorized user, you
Page 73 and 74: Command Description: Command enable
Page 75 and 76: 4.4.1.3 Annex There are two types o
Page 77 and 78: 4.4.3 VLAN Virtual LAN (VLAN) is de
Page 79 and 80: Access Trunk The port can receive o
Page 81 and 82: 4.4.4.2 Queue weight This setting c
Page 83 and 84: 4.4.4.5 VLAN Tag Priority QoS -----
Page 85 and 86: 4.4.5 RATE Move the cursor " >> " t
Page 87 and 88: To configure DHCP server, move the
Page 89 and 90: 4.4.9 Host name A Host Name is the
Page 91 and 92: 4.5.2 Interface Move cursor " >> "
Page 93 and 94: 4.9 Ping Ping command can use to di
Page 95 and 96: Move the cursor ">>" to attrib and
Page 97 and 98: 4.10.3 SNMP Simple Network Manageme
Page 99 and 100: SNMP Trap Host: Trap Host entry(1~5
Page 101 and 102: 4.11.1 Upgrade main software Move t
Page 103 and 104: 5 Appendix - Setup table SHDSL.bis:
Page 105 and 106: QoS Mode: QoS Mode □Disable □Po
Page 107: SNMP Community: SNMP entry (1) Vali
show all

EFM User Manual - CTC Union Technologies Co.,Ltd.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?