Phoenix Contact INTERFACE System Cabling and ... - Power/mation
Phoenix Contact INTERFACE System Cabling and ... - Power/mation
Phoenix Contact INTERFACE System Cabling and ... - Power/mation
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>INTERFACE</strong> <strong>Cabling</strong><br />
VARIOFACE wiring interface<br />
Solder-in socket for solid-state relays<br />
<strong>and</strong> I/O modules<br />
Modern interface solutions for computer<br />
<strong>and</strong> electronic controls are increasingly<br />
being designed as I/O systems which are<br />
system independent <strong>and</strong> individually<br />
mountable. Electrical isolation <strong>and</strong> signal<br />
conditioning are carried out using st<strong>and</strong>ard<br />
I/O modules. These are produced by<br />
various manufacturers in pin-compatible<br />
versions for different functions. The I/O<br />
modules are either soldered directly into<br />
the PCB or plugged into component<br />
sockets for quick interchanging.<br />
SIM sockets facilitate the plugging of I/O<br />
modules considerably. All st<strong>and</strong>ard I/O<br />
modules <strong>and</strong> solid-state relays with up to<br />
eight connections can be plugged into the<br />
solder-in plug-in socket.<br />
The I/O modules are securely fixed to the<br />
socket using fastening screws which are<br />
specific to the module. They are thereby<br />
protected against being accidentally<br />
released. Optocouplers, now also available<br />
in pluggable versions, are secured using the<br />
latch which is attached to the socket <strong>and</strong><br />
which can be labeled. For better<br />
identification, each module plug position has<br />
its own marking panel on the socket.<br />
The SIM socket has been designed so that<br />
it can be used on existing printed circuit<br />
boards without any layout modifications.<br />
Peripheral components such as LEDs or<br />
fuse resistors remain accessible to the user.<br />
Note:<br />
Dimensional drawings <strong>and</strong> contacts, refer<br />
to page 316.<br />
Notes:<br />
Type of housing:<br />
Polyamide PA non-reinforced, color: green.<br />
For marking systems <strong>and</strong> mounting material, see CLIPLINE catalog.<br />
1) Applies only to the sockets SIM-AMS 1, SIM-AMS 1-R <strong>and</strong> SIM-<br />
AMSC in connection with the st<strong>and</strong>ard I/O modules with the<br />
corresponding AC voltage output.<br />
Description<br />
No. of<br />
pos.<br />
Plug-in base, for solid-state relay <strong>and</strong> I/O modules, with different<br />
numbers of contacts, can be labeled with marker pins BN or BNB<br />
Module width<br />
W Type Order No. Pcs. /<br />
Pkt.<br />
Partial assembly SIM-AMS 1 2271015 10<br />
Complete assembly SIM-AMS 2 2271028 10<br />
Plug-in base, as above, however, with locking clips for fastening<br />
Partial assembly<br />
Complete assembly<br />
Plug-in base, for st<strong>and</strong>ard I/O modules of generation 4 of the<br />
company Opto 22, can be labeled using marker pins BN or BNB<br />
Marker pin, made of white plastic, lettering area 7.5 x 4 mm,<br />
unprinted for self-marking with B-STIFT<br />
BN-TRK 2701404 100<br />
Marker pen, not refillable, for manual labeling, line thickness<br />
0.5 mm<br />
B-STIFT 1051993 10<br />
Technical data<br />
Operating voltage 250 V AC / 380 V AC 1 )<br />
Nominal current<br />
St<strong>and</strong>ards/regulations<br />
SIM-AMS...<br />
5 A<br />
DIN VDE 0110b, Gr. C for 250 V DC<br />
A C P<br />
312 PHOENIX CONTACT<br />
Courtesy of <strong>Power</strong>/<strong>mation</strong>. 1310 Energy Lane, Saint Paul, MN 55108<br />
info@power<strong>mation</strong>.com - 800-843-9859 - www.power<strong>mation</strong>.com