PDF catalog - Who-sells-it.com

CRATE ENGINES SMALL-BLOCK
Complete Your Small-Block Crate Engine
Select the parts below to finish off your crate engine and get running in less time!
10185063
Intake Manifold
Our low-profile, dual-plenum aluminum
intake manifold helps make great power
and fits under the hood of almost every
vehicle. Accommodates both Holley
4160-Series and Quadrajet carburetors.
12496822
Intake Manifold, Vortec Eliminator
This aluminum, single-plane intake manifold
is designed for use with Vortec cylinder
heads P/N 12558060, 25534421, 25334446,
Fast Burn heads P/N 12464298, or Vortec
Bowtie heads P/N 25534421 and 25534426
to build maximum power and torque.
Requires manifold bolts P/N 12550027.
12366573
Intake Manifold, Vortec Design
Designed for Small-Block engines up to
400-cu-in and equipped with Vortec-type
cylinder heads, this high-rise aluminum
intake manifold has a dual-plane design
that helps the engine deliver a strong
balance of horsepower and torque.
12342089
Small-Block Chrome
Timing Cover
This attractive chrome cover fits
1969-1991 Small-Block V-8 and 90-degree
V-6 engines. It is a direct replacement for
covers that use a bolt-on timing pointer
and it includes the oil seal.
12341998
Fuel Pump Block-Off Plate
This attractive chrome plate is embossed
with the Chevrolet Bowtie logo. It is
used in place of a mechanical fuel pump
on the engine block. Includes a nonasbestos
gasket.
12355612
Fuel Pump, Street Performance
Use this mechanical fuel pump on
carbureted engines. It has 7-psi shutoff
pressure and a free-flow rate of 110 gph.
The lower housing can be rotated to
reposition the inlet and outlet ports to
suit different applications.
12480127
Short Aluminum Valve Covers
This racing-inspired design has the
Bowtie logo and Chevrolet lettering. The
cast aluminum covers include PCV holes
(grommets included) and oil baffles.
12341670
Chrome Short Valve Covers
Add sparkle to your Small-Block with
these classic chrome valve covers,
designed for pre-1986 cylinder heads
with perimeter-style hold-down bolts.
The covers feature the Bowtie logo and
Chevrolet name.
12497979
Aluminum Black Crinkle Valve
Covers, Center Bolt Design
Valve covers with red Chevrolet Bowtie
logo. They include PCV holes (grommets
included) and are approximately ¼" taller
than production. Kit includes bolts, washers
and seals. NOTE: Use valve cover
gasket P/N 10046089.
ALSO AVAILABLE
350 Hot Cam Kit 12480002
Bolt (Motor Mount — 2 req.) 460308
Carburetor, Holley 770-cfm 19170093
Fan 19.5" (Serpentine Belt) 15563127
Fan 19.5" (V-belt) 15644302
Fan Bolts—4 req. 9440224
Fan Clutch (Serpentine Belt) 19150657
Fan Clutch (V-belt) 88961767
Fan Stud Nuts—4 req. 12338130
Fan Studs—4 req. (Serpentine Belt) 12338107
Fan Studs—4 req. (V-belt) 382919
Fuel Pump—High Capacity Small-Block 6415325
Harmonic Balancer 12551537
Magnetic Drain Plug 24241872
Motor Mount—2 req. (Car) 22188497
Motor Mount—2 req. (Truck) 15731260
CRATE ENGINES SMALL-BLOCK
88894341
Water Pump, Long-Style
The later-style, cast-iron water pump has
the long leg design, reinforced snout and
a 3/4-inch snout (reduced to 5/8-inch at
end of shaft). Use it with the 350 HO,
383 and ZZ4 engines.
88965829
CNC’d Carburetor Spacer, Dual-
Plane 1-inch
Fully machined from billet aluminum,
this lightweight 1-inch spacer carries the
GM Performance Parts logo on the front
and rear. It fits Quadrajet-type and Holley
carburetors.
12497985
Chrome-Finish Aluminum Valve
Covers, Center Bolt Design
Valve covers feature the Chevrolet
Bowtie logo and include PCV holes
(grommets included). Approximately
¼-inch taller than production. Kit includes
bolts, washers and seals. NOTE: Use
valve cover gasket P/N 10046089.
Oil Filler Cap—Push-In 12341993
Oil Filter Adapter 3952301
Roller Rocker Arm Kit, 1.5:1 Ratio—Aluminum 12370838
Roller Rocker Arm Set, 1.6:1 Ratio—Aluminum 12370839
Serpentine Accessory Drive Belt System, Deluxe 12497698
Serpentine Accessory Drive Belt System, without A/C 12497697
93440806
HEI Distributor
This high-energy electronic distributor
is a must for steel roller cams. It offers
ignition advance curve for high-performance
applications.
12368084
Engine Oil Primer Tool
Use to prelube the engine bearings and
prime the oiling system prior to starting a
new crate engine. Requires electric drill
or similar (not included).
12342071
Air Cleaner, Classic Design
A classic in chrome, this 14" round air
cleaner has the Chevrolet name and a
Bowtie wing nut. It fits most two- and
four-barrel carburetors.
Spark Plug Wires, Red GM Performance 135° Boot 12361056
Spark Plug Wires, Red GM Performance 90° Boot 12361057
Standard Starter (Offset Bolt Holes) 10496873
Standard Starter (Straight Bolt Holes) 10496871
Transmission Mount (4L60 & 4L80) 15767858
Transmission Mount (700R4) 2218814
88961867
Distributor, Aluminum Billet HEI
Distributor features a CNC-machined
aluminum housing, ball bearing guide,
oversized shaft and long-sintered bushing
for durability. It also has mechanical and
vacuum advance. Brass terminal cap.
Connector P/N 12167658 attaches tach
and 12-volt power supply wire.
12361146
High-Torque Mini-Starter
Designed to deliver powerful starting
capability in a compact size, this highperformance
gear-reduction starter fits
153- or 168-tooth flywheels.
12342080
Air Cleaner, Chevrolet-Logo
High-Performance Design
14" round high-performance-style air
cleaner. Chrome lid with embossed
Chevrolet name. Fits most four-barrel and
two-barrel carburetors.
Transmission Mount (700R4) 22188145
Transmission Mount (TH400) 17990778
Valve Covers—Polished Aluminum 12497978
Valve Cover Adapter—Centerbolt to Flange Mount 24502540
Valve Covers—Polished Aluminum, Die-Cast 12363970
12342024
Chrome Water Neck
Add a bit of chrome to your engine with
this detailed water neck. It includes a
neoprene O-ring and chrome fasteners.
It fits 1966-1975 Chevrolet, Camaro and
Chevelle models with V-8 engines.
10465143
Lightweight Starter
(remanufactured)
Originally designed for 1993-97 Camaros
and Firebirds equipped with the LT1 engine,
this lightweight, high-performance
starter can be used on any Small-Block
or Big-Block engine with a 12.75-inch,
153-tooth flywheel.
19170092
Carburetor, Holley 670-cfm
Holley’s 4160-style 670-cfm four-barrel
carburetor is perfect for many crate
engines. It has show-quality polished
details, center-hung fuel bowls, vacuum
secondaries and power valve blowout
protection.
Water Pump, Long-Style—Aluminum 12495826
Water Pump, Short-Style—Aluminum 14011012
Wire Loom Kit, Small-Block 12496806
Available for purchase online at
gmperformanceparts.com
56 Buy online at www.gmperformanceparts.com
Buy online at www.gmperformanceparts.com
57