Owners Manual - Roland
Owners Manual - Roland
Owners Manual - Roland
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Troubleshooting<br />
If you think there’s a problem, read this first.<br />
Symptom Cause/Action Page<br />
Power will not turn on Is the power cord correctly connected to the VR-700 and to an AC outlet? p. 18<br />
Buttons don’t work<br />
Could Panel Lock be enabled?<br />
Hold down the HARMONIC BAR [LOWER] button and press the PLAYER [RHYTHM] button to<br />
release Panel Lock.<br />
Could the VR-700 be in Demo mode?<br />
Press the [DISPLAY/EXIT] button to exit Demo mode.<br />
p. 25<br />
p. 23<br />
Is your playback equipment (amp and speaker) powered up? p. 19<br />
Could the volume of your playback system (amp and speaker) have been lowered?<br />
Check the volume of your playback system.<br />
p. 19<br />
Are your amp, speakers, or headphones connected correctly? p. 21<br />
No sound/Insufficient volume<br />
Organ sound is not heard<br />
Could the VR-700’s volume be lowered?<br />
Check the setting of the [MASTER VOLUME] knob and the [ENSEMBLE VOLUME] bar.<br />
Could the expression pedal have been used to adjust the volume?<br />
While being careful about the volume depress, step on the pedal.<br />
Could the Local Control setting be off?<br />
Turn the Local Control setting on again, or turn the VR-700’s power off, then on again.<br />
Could all of the harmonic bars be pushed in?<br />
Pull the harmonic bars toward yourself.<br />
Could the wheel brake key be applied?<br />
Use the foot switch or D Beam to release the wheel brake.<br />
p. 14<br />
p. 23<br />
p. 45<br />
p. 57<br />
p. 38<br />
p. 43<br />
Ensemble sound is inaudible or<br />
not loud enough<br />
Pull out the [ENSEMBLE VOLUME] lever to increase the volume of the ensemble sound. p. 14<br />
Could the volume have been adjusted by the expression pedal?<br />
If the Ensemble Expression Switch is on, the volume of the ensemble sound will be controlled<br />
by the expression pedal. While being careful about the volume, depress the expression pedal.<br />
p. 54<br />
Noise is heard when you press or<br />
release a key<br />
Pitch is incorrect<br />
Harmonic bar 1’ is not heard<br />
MIDI messages are not<br />
transmitted/received correctly<br />
Pedal doesn’t work, or is stuck<br />
Can’t read/write USB memory<br />
This is not a malfunction.<br />
The VR-700 reproduces the noise that is heard when a key of a tonewheel organ is turned on/<br />
off. You can eliminate this noise by setting the Function mode Key On Click Level and Key Off<br />
Click Level settings to 0.<br />
Could the tuning be incorrect?<br />
The pitch of the organ sounds can be adjusted by the Function mode setting “Organ Fine Tune”<br />
(p. 52), and the pitch of the ensemble sounds can be adjusted by the “Ensemble Fine Tune”<br />
setting (p. 53) The overall pitch is adjusted by “Master Tune” (p. 59). Check these settings.<br />
Could the VR-700 be transposed?<br />
Either disable the transpose setting, or re-specify it.<br />
Could the wheel brake have been left on?<br />
Operate the foot switch or D Beam, to release the wheel brake.<br />
Could percussion be on?<br />
If percussion is on, the 1’ harmonic bar will not sound.<br />
Is each part’s MIDI channel set correctly?<br />
In the Function mode MIDI group of settings, specify the correct MIDI transmit/receive channel<br />
for each part.<br />
Is the pedal connected correctly?<br />
Check the pedal connections.<br />
Is the pedal polarity set correctly?<br />
Set the Function mode parameters “Damper Pedal Polarity” and “Control Pedal Polarity”<br />
appropriately for the polarity of the pedal you are using.<br />
If you connect a pedal while the power is on, the pedal effect may be “stuck.” Make sure that<br />
you connect pedals after you’ve switched off the VR-700’s power.<br />
Have you assigned a function to the pedal?<br />
A variety of functions can be assigned to the pedal connected to the CONTROL PEDAL<br />
connector. Check the Function mode setting “Control Pedal Assign.”<br />
Are you using USB memory (sold separately) made by <strong>Roland</strong>?<br />
We cannot guarantee operation if other USB memory is used.<br />
If you’re unable to read or write USB memory, try changing the Function mode setting “USB<br />
Memory Mode.”<br />
p. 45<br />
–<br />
p. 59<br />
p. 43<br />
p. 41<br />
p. 57<br />
p. 20<br />
p. 54<br />
–<br />
p. 54<br />
–<br />
p. 59<br />
77