FIRE DESIGN OF STEEL MEMBERS - Civil and Natural Resources ...

More documents

Recommendations

Info

22 FISO 23 FISO FISO 24 FISO FISO 25 FISO FISO 26 FISO FISO 27 FISO FISO FISO SYMMETRY ENDSYM MATERIALS <strong>STEEL</strong>EC2 9 0.5 25 159
DIAMOND OUTPUT From the Diamond output programme, this is the temperature layout showing the temperature of the different elements at a chosen time: Figure B.2: Output window of the Diamond programme. 160
Page 1 and 2:
Fire Design of Steel Members K R Le
Page 4:
ABSTRACT: The New Zealand Steel Cod
Page 8 and 9:
TABLE OF CONTENTS: ABSTRACT:.......
Page 10 and 11:
5.4 RESULTS FOR FOUR SIDED EXPOSURE
Page 12 and 13:
LIST OF FIGURES: FIGURE 1.1: VARIAT
Page 14:
FIGURE 5.11: TEMPERATURE CONTOUR LI
Page 17 and 18:
designed with confidence. Full scal
Page 19 and 20:
eams and struts when subjected to a
Page 21 and 22:
Gilvery and Dexter, (1997), prepare
Page 23 and 24:
with conditions specified to ensure
Page 25 and 26:
1.6 BACKGROUND INFORMATION: 1.6.1 F
Page 27 and 28:
experienced in fire situations, but
Page 29 and 30:
The thermal conductivity is not imp
Page 31 and 32:
[ The heated perimeter of the steel
Page 33 and 34:
The advantages of board systems are
Page 35 and 36:
The values for the thermal properti
Page 37 and 38:
insulation has on the rise of the s
Page 39 and 40:
( T − T ) k H p f s ∆t ∆T
Page 41 and 42:
spreadsheet method very closely, wi
Page 43 and 44:
protection, and for user defined fi
Page 45 and 46:
This equation originates from the y
Page 47 and 48:
1400 1200 1000 800 600 400 200 0 0.
Page 49 and 50:
time. The value of the wall lining
Page 51 and 52:
The Eurocode does not define a meth
Page 53 and 54:
f f y y ( T ) (20) = 1.0 0 < T < 21
Page 55 and 56:
temperature is chosen because it is
Page 57 and 58:
The variation of yield stress data
Page 59 and 60:
15 m -1 < H p /A < 275 m -1 in NZS
Page 61 and 62:
= H p A (m -1 ) 7.85 The cons
Page 63 and 64:
Connections: NZS 3404 requires that
Page 66 and 67:
4 CALCULATION OF STEEL TEMPERATURES
Page 68 and 69:
4.1.2 Analysis Between Methods of T
Page 70 and 71:
Figure 4.2 shows the variation of t
Page 72 and 73:
Minimum temperatures Maximum temper
Page 74 and 75:
For all three sizes of beam, the sp
Page 76 and 77:
Temperature ( o C) 1200 1000 800 60
Page 78 and 79:
The ECCS equation has a time period
Page 80 and 81:
4.3.1 Results from simulations with
Page 82 and 83:
From Figure 4.5 a-c, the formula ra
Page 84 and 85:
Temperature ( o C) 1000 800 600 400
Page 86 and 87:
average temperature of the beam, be
Page 88 and 89:
Temperature ( o C) 1400 1200 1000 8
Page 90 and 91:
significantly decreased from a cool
Page 92 and 93:
Since both programmes use the same
Page 94 and 95:
Therefore, the ECCS equations provi
Page 96 and 97:
5 CALCULATION OF STEEL TEMPERATURES
Page 98 and 99:
calculations made by the spreadshee
Page 100 and 101:
susceptible to heating, heat up mor
Page 102 and 103:
Figure 5.3 a-c show the results fro
Page 104 and 105:
7850*600*10500 > 2*775*1100*(1869*2
Page 106 and 107:
As can be seen from Figure 5.4 a-c,
Page 108 and 109:
310 UB 40.4 beam H p /A = 241 m -1
Page 110 and 111:
The SAFIR results fit between the t
Page 112 and 113:
constant specific heat being used i
Page 114 and 115:
From Figure 5.7 a-c, it appears tha
Page 116 and 117:
800 Temperature ( o C) 600 400 200
Page 118 and 119:
To examine the limits of the thickn
Page 120 and 121:
1000 Temperature ( o C) 800 600 400
Page 122 and 123:
Thermal conductivity, k i = 0.19 W/
Page 124 and 125: 1000 Temperature ( o C) 800 600 400
Page 126 and 127: the slab except to reduce the secti
Page 128 and 129: Figure 5.14 shows the correlation b
Page 130 and 131: 5.8 CONCLUSIONS: The thermal behavi
Page 132 and 133: 6 COMPARISON OF METHODS USING OTHER
Page 134 and 135: Temperature ( o C) 1200 1000 800 60
Page 136 and 137: 6.2.4 Results for protected steel:
Page 138 and 139: Figures 6.2 b shows the comparison
Page 140 and 141: Figure 6.3 a shows that the average
Page 142 and 143: The fire that the test beams were e
Page 144 and 145: 7 ADDITIONAL MATERIAL IN EUROCODE 3
Page 146 and 147: For thermal analysis in Eurocode 3,
Page 148 and 149: To determine the performance of a s
Page 150 and 151: The plastic neutral axis is located
Page 152 and 153: It is therefore recommended that th
Page 154 and 155: These methods may be used to provid
Page 156: Eurocode has a large annex with gui
Page 159 and 160: 8.3 CHANGES TO NZS 3404: The follow
Page 161 and 162: H v height of the ventilation (m) I
Page 163 and 164: EC3, 1995. Eurocode 3: Design of St
Page 165 and 166: Temperature Conditions. National Re
Page 168 and 169: APPENDIX A - SPREADSHEET METHOD: Be
Page 170 and 171: APPENDIX B - SAFIR: In Figure B.2 i
Page 172 and 173: *.str file developed by the pre pro
Page 176: APPENDIX C - FIRECALC Below in Figu
show all

FIRE DESIGN OF STEEL MEMBERS - Civil and Natural Resources ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?