3to 11hp 4-cycle l-head engines - Small Engine Suppliers

More documents

Recommendations

Info

TROUBLESHOOTING ELECTRICAL STARTER CIRCUIT FLOW CHART Starter will not turn Intermittent starter operation Starter turns at low rpms or stalls under load NO Is there power at the power source YES Repair or replace power source NO Is power supplied to the starter terminal YES Check wiring, connections, safety switches, starter switch NO Isolate engine from the equipment, does engine turn over YES Check starter for binding brushes, worn brushes, dirty or oily commutator NO Internal engine failure or flywheel interference Remove spark plug, does engine turn over freely NO YES Reinstall spark plug, does engine bind on compression stroke Repair or replace equipment causing excessive loading YES YES Check valve lash. Adjust if necessary. Does the engine turn over without binding now NO Repair or replace electric starter Internal engine failure, repair or replace engine 46
TROUBLESHOOTING ELECTRICAL CHARGING CIRCUIT FLOW CHART Identify the charging system used by model and specification number or visually check the electrical plug Consult the Technician's Handbook or Electrical Troubleshooting booklet for test procedure for the charging system used Test for either AC or DC voltage as directed at the proper engine RPM NO Is the voltage greater than or equal to the minimum value YES NO Is AC voltage before diode or rectifier greater than the minimum value YES Check wiring, switches, or ammeter for breaks, shorts Alternator coil failure, replace coil assy. Check diodes, replace if no continuity exists or if continuity exists reversing test leads Check fuses, replace as necessary Check switches, wiring, or lights for shorts 47
Page 1 and 2: TECUMSEH T E C H N I C I A N ' S H
Page 3 and 4: GOVERNOR GEAR AND SHAFT SERVICE....
Page 5 and 6: CHAPTER 1 GENERAL INFORMATION ENGIN
Page 7 and 8: ENGINE OIL Use a clean, high qualit
Page 9 and 10: GENERAL INFORMATION CHAPTER 2 AIR C
Page 11 and 12: CHAPTER 3 CARBURETORS AND FUEL SYST
Page 13 and 14: IMPULSE FUEL PUMPS Impulse fuel pum
Page 15 and 16: CARBURETOR IDENTIFICATION Tecumseh
Page 17 and 18: ENGINE TROUBLESHOOTING Engine Will
Page 19 and 20: TESTING 1. After repeated efforts t
Page 21 and 22: DISASSEMBLY PROCEDURE NOTE: Engines
Page 23 and 24: Diaphragm Carburetors 1. Remove the
Page 25 and 26: ASSEMBLY Welch Plugs To install a n
Page 27 and 28: 4. Install the hinge pin from the o
Page 29 and 30: Throttle Lever Remove the throttle
Page 31 and 32: ENGINE OVERSPEEDING 1. If the engin
Page 33 and 34: SPEED CONTROLS AND LINKAGE Many dif
Page 35 and 36: HORIZONTAL SHAFT ENGINES IDLE SPEED
Page 37 and 38: VERTICAL SHAFT ENGINES HIGH SPEED A
Page 39 and 40: GENERAL INFORMATION CHAPTER 5 REWIN
Page 41 and 42: CAUTION: THIS REWIND SPRING IS NOT
Page 43 and 44: 2. Place the pulley assembly into t
Page 45 and 46: at the outer edge against the gear
Page 47 and 48: CONVERTING ALTERNATING CURRENT TO D
Page 49: BASIC CHECKS Before going into exte
Page 53 and 54: 18 Watt A.C. Lighting Alternator Mo
Page 55 and 56: NOTE: ON OLDER POINT IGNITION SYSTE
Page 57 and 58: 5 Amp Alternator System Regulator-R
Page 59 and 60: 7 Amp Alternator System Regulator-
Page 61 and 62: SERVICE This section covers the ser
Page 63 and 64: CHAPTER 7 FLYWHEEL BRAKE SYSTEMS GE
Page 65 and 66: SERVICE If the brake system fails t
Page 67 and 68: CHAPTER 8 IGNITION GENERAL INFORMAT
Page 69 and 70: The condenser acts as an electrical
Page 71 and 72: TESTING PROCEDURE 1. Check for spar
Page 73 and 74: Begin the procedure by replacing th
Page 75 and 76: Other Solid State Systems The follo
Page 77 and 78: LUBRICATION SYSTEMS The lubrication
Page 79 and 80: ENGINE OPERATION PROBLEMS ENGINE KN
Page 81 and 82: TESTING ENGINE KNOCKS 1. Check the
Page 83 and 84: 5. Check the engine valve lash. Res
Page 85 and 86: CYLINDERS Visually check the cylind
Page 87 and 88: Use a ring expander to remove and r
Page 89 and 90: VALVES The valves should be checked
Page 91 and 92: Late production top mounted breathe
Page 93 and 94: COUNTERBALANCE SERVICE To correctly
Page 95 and 96: FOUR CYCLE TORQUE SPECIFICATIONS Th
Page 97 and 98: ENGINE SPECIFICATIONS STANDARD POIN
Page 99 and 100: ENGINE SPECIFICATIONS STANDARD POIN
Page 101 and 102:
SOLID STATE AND EXTERNAL IGNITION A
Page 103 and 104:
SOLID STATE AND EXTERNAL IGNITION A
Page 105 and 106:
SOLID STATE AND EXTERNAL IGNITION (
Page 107 and 108:
OIL SEAL DRIVER FLYWHEEL KNOCK-OFF
Page 109 and 110:
DECIMAL/FRACTION CONVERSIONS .016 =
Page 111 and 112:
SEARS CRAFTSMAN CROSS REFERENCE CHA
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
show all

3to 11hp 4-cycle l-head engines - Small Engine Suppliers

Create successful ePaper yourself

Delete template?

Save as template?