D1 H.264 M Series DVR User Manual

More documents

Recommendations

Info

NAME Set the channel name. Press the right square button and set the channel name and select OK using the mouse or the control button (◀ ▲ ▶ ▼) on the remote control. The name can be made by 10 characters at most. COVERT Enable/disable display of the specified video channel in live display mode. BRIGHTNESS Change the brightness value of the specified channel. (0~100) CONTRAST Change the contrast value of the specified channel. (0~100) HUE Change the hue value of the specified channel. (0~100) SATURATION Change the saturation value of the specified channel. (0~100) 3-3. Setup – Recording Mode Press the SETUP button and select RECORD icon. Then, the RECORD menu is displayed as picture below. Navigate through the menu items using the mouse or the control button (◀ ▲ ▶ ▼) on the remote control and change the value of the menu item. 24
Figure 3.3.1. Recording mode setup screen CHANNEL Menu item Table 3.3.1. Menu items in Recording mode setup Description Select a channel for applying the following settings using the mouse or the control button (◀ ▲ ▶ ▼) on the remote control. Press the right square button to change the setting value of all channels at once. Once you select an item, then press OK to set value for all channels. (RESOLUTION, FRAME RATE, QUALITY, RECORDING, PRE RECORD and POST EVENT RECORD) RESOLUTION Select one type among CIF, Half D1 and D1 using the mouse or the control button(◀ ▲ ▶ ▼) on the remote control. FRAME RATE Set the frame rate for the specified channel. The sum of the frame rate values from each channel cannot exceed the maximum frame rates for a specific recording resolution. Typical values of the maximum frame rate for video are as follows. CIF Half D1 D1 N-0440M 120/100fps 120/100fps 120/100fps N-0840M 240/200fps 240/200fps 120/100fps N-1640M 480/400fps 240/200fps 120/100fps 25
Page 1 and 2: INSTRUCTION MANUAL (N:M_Ver. 2.1_11
Page 3 and 4: These precautions must be followed
Page 5 and 6: Product Components The package cont
Page 7 and 8: Mounting the HARD DISK 1. Before in
Page 9 and 10: Specifications Input Video Output A
Page 11 and 12: Table of Contents 1. Main Features
Page 13 and 14: 9-7-6. Security ...................
Page 15 and 16: Easy software upgrade Instant and
Page 17 and 18: 13 Press to control Pan/Tilt/Zoom o
Page 19 and 20: 3 Number: To select channel (1, 2,
Page 21 and 22: - QUALITY - RECORDING - SENSOR RECO
Page 23: - DUAL FRAME RATE - DUAL QUALITY 3-
Page 27 and 28: Figure 3.3.2. Schedule recording se
Page 29 and 30: Item Description ALARM OUT Availabl
Page 31 and 32: Figure 3.4.4. PTZ Control Setup Scr
Page 33 and 34: We recommend that you archive any d
Page 35 and 36: SET DATE&TIME Select the display da
Page 37 and 38: PRIMARY SNTP SERVER: Input the addr
Page 39 and 40: USER PASSWORD ADMIN, NETOWRK, USER1
Page 41 and 42: NETWORK PORT Set a proper port numb
Page 43 and 44: Table 3.8.2. LAN Item Description I
Page 45 and 46: Figure 3.8.6. Network setup screen
Page 47 and 48: Item SAVE SETUP TO A USB Table 3.9.
Page 49 and 50: Figure 3.10.1. Quick Setup screen I
Page 51 and 52: Audio button. Click this button to
Page 53 and 54: When it clicks a Timeline menu, use
Page 55 and 56: When it clicks an Archive menu, use
Page 57 and 58: Figure 5.1. PTZ Control Screen OSD
Page 59 and 60: 3. Once you select the media, the s
Page 61 and 62: 7. Upgrading Firmware In order to u
Page 63 and 64: 8-3. Live monitoring mode and funct
Page 65 and 66: 3. Set the conditions and click OK
Page 67 and 68: 4. Press the PLAY button. Then the
Page 69 and 70: Setting Event Set the record path a
Page 71 and 72: 9. Network access using the Exclusi
Page 73 and 74: 9-4-1. Main user interface 9-4-2. C
Page 75 and 76:
8-5-2. Main control panel Button LO
Page 77 and 78:
To change a time line scale from 24
Page 79 and 80:
9-6-2-2. Archiving Event Log: Event
Page 81 and 82:
9-6-6. About “About” provides n
Page 83 and 84:
Resolution: Sets the resolution for
Page 85 and 86:
9-7-3-3. PTZ Setting the PTZ Contro
Page 87 and 88:
9-7-5-1. System Setting the System
Page 89 and 90:
Setting the Send E-Mail: This setti
Page 91 and 92:
9-7-7.Network Select Network to set
Page 93 and 94:
o Password: Input network password
Page 95 and 96:
2. Click CONNECT button, and then s
Page 97 and 98:
3. Select Disk and set the values.
Page 99 and 100:
2. Select site to connect from the
Page 101 and 102:
Notice When it does a backup with N
Page 103 and 104:
Server address: Input IP address of
Page 105 and 106:
Open your web browser. Enter the ro
Page 107 and 108:
Internet (ADSL) Connection using DD
Page 109 and 110:
C. How to access DVR with iPhone 1.
show all

D1 H.264 M Series DVR User Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?