D1 H.264 M Series DVR User Manual

More documents

Recommendations

Info

When it changes the VGA resolution and saves the value, the system will reboot. When it changes the VGA resolution to 1280x1024, the CVBS is set to Off. ALARM OUT Set the sensor, motion, and video loss for each alarm. PTZ Set the PTZ camera speed, number, type and ID. SPOT-OUT Set the all details for spot monitoring. It supports 2 spot-outs. CHANNEL Select specified channel for motion zone setup. MOTION ZONE Select either Full Zone or Partial Zone for motion sensing. MOTION SENSITIVITY Set the motion sensitivity for the specified channel. Control the motion sensitivity from 1 to 9. KEY TONE Enable/disable key tone. REMOTE CONTROL ID Select an ID of remote control. 1. Select ID. 2. Press the same number as ID set in <strong>DVR</strong> on a remote control. 3. Then icon will be displayed on Live screen of <strong>DVR</strong> that respond to the remote control. The options are from 0 to 99 SENSOR Select sensor NO from 1 to 4 TYPE Set the type of sensor for the specified channel. Options are: OFF, N/O (normal open), and N/C (normal closed). 3-4-1. ALARM-OUT Figure 3.4.2. ALARM-OUT setup screen Table 3.4.2. Menu item in ALARM-OUT Setup screen 28
Item Description ALARM OUT Available NO is just one (1). SENSOR IN Enable setting up to 1 camera of 4 cameras for each alarm. MOTION ON Enable setting up to 1 camera of 4 cameras for each alarm. VIDEO LOSS ON Enable setting up to 1 camera of 4 cameras for each alarm. ALARM DURATION Set the alarm dwell time from 5 to 60 seconds. ERROR ALARM Set the error type for the alarm activation. The options are OFF, ALL, HDD ERROR and VIDEO LOSS. 3-4-2 SPOT-OUT setup Figure 3.4.3. SPOT-OUT setup screen Table 3.4.3. Menu item in SPOT-OUT Setup screen N-0441L supports just 1 Spot Out. Item Description SPOT OUT 1 To use the Spot out function, it has to change CVBS to OFF in a Video Output menu. SPOT TYPE Spot out 1 supports FULL type. (1 channel only) SPOT ON EVENT Enable/Disable display of the channel when an event is active. SPOT EVENT Set the dwell time for the display of the event activated channel. DWELL TIME (1-10sec) SEQUENCE Enable/disable sequential display of spot channel in full screen. If select ON, spot channel selection screen is displayed. SEQ-DWEL TIME Set the dwell time for the spot channel display.(1-10sec) SPOT CHANNEL Select a channel for spot monitoring using the mouse or the control button (◀ ▲ ▶ ▼) on the remote control and press OK button. 29
Page 1 and 2: INSTRUCTION MANUAL (N:M_Ver. 2.1_11
Page 3 and 4: These precautions must be followed
Page 5 and 6: Product Components The package cont
Page 7 and 8: Mounting the HARD DISK 1. Before in
Page 9 and 10: Specifications Input Video Output A
Page 11 and 12: Table of Contents 1. Main Features
Page 13 and 14: 9-7-6. Security ...................
Page 15 and 16: Easy software upgrade Instant and
Page 17 and 18: 13 Press to control Pan/Tilt/Zoom o
Page 19 and 20: 3 Number: To select channel (1, 2,
Page 21 and 22: - QUALITY - RECORDING - SENSOR RECO
Page 23 and 24: - DUAL FRAME RATE - DUAL QUALITY 3-
Page 25 and 26: Figure 3.3.1. Recording mode setup
Page 27: Figure 3.3.2. Schedule recording se
Page 31 and 32: Figure 3.4.4. PTZ Control Setup Scr
Page 33 and 34: We recommend that you archive any d
Page 35 and 36: SET DATE&TIME Select the display da
Page 37 and 38: PRIMARY SNTP SERVER: Input the addr
Page 39 and 40: USER PASSWORD ADMIN, NETOWRK, USER1
Page 41 and 42: NETWORK PORT Set a proper port numb
Page 43 and 44: Table 3.8.2. LAN Item Description I
Page 45 and 46: Figure 3.8.6. Network setup screen
Page 47 and 48: Item SAVE SETUP TO A USB Table 3.9.
Page 49 and 50: Figure 3.10.1. Quick Setup screen I
Page 51 and 52: Audio button. Click this button to
Page 53 and 54: When it clicks a Timeline menu, use
Page 55 and 56: When it clicks an Archive menu, use
Page 57 and 58: Figure 5.1. PTZ Control Screen OSD
Page 59 and 60: 3. Once you select the media, the s
Page 61 and 62: 7. Upgrading Firmware In order to u
Page 63 and 64: 8-3. Live monitoring mode and funct
Page 65 and 66: 3. Set the conditions and click OK
Page 67 and 68: 4. Press the PLAY button. Then the
Page 69 and 70: Setting Event Set the record path a
Page 71 and 72: 9. Network access using the Exclusi
Page 73 and 74: 9-4-1. Main user interface 9-4-2. C
Page 75 and 76: 8-5-2. Main control panel Button LO
Page 77 and 78: To change a time line scale from 24
Page 79 and 80:
9-6-2-2. Archiving Event Log: Event
Page 81 and 82:
9-6-6. About “About” provides n
Page 83 and 84:
Resolution: Sets the resolution for
Page 85 and 86:
9-7-3-3. PTZ Setting the PTZ Contro
Page 87 and 88:
9-7-5-1. System Setting the System
Page 89 and 90:
Setting the Send E-Mail: This setti
Page 91 and 92:
9-7-7.Network Select Network to set
Page 93 and 94:
o Password: Input network password
Page 95 and 96:
2. Click CONNECT button, and then s
Page 97 and 98:
3. Select Disk and set the values.
Page 99 and 100:
2. Select site to connect from the
Page 101 and 102:
Notice When it does a backup with N
Page 103 and 104:
Server address: Input IP address of
Page 105 and 106:
Open your web browser. Enter the ro
Page 107 and 108:
Internet (ADSL) Connection using DD
Page 109 and 110:
C. How to access DVR with iPhone 1.
show all

D1 H.264 M Series DVR User Manual

Create successful ePaper yourself

Delete template?

Save as template?