2010 Kenworth T440/T470 Body Builder Manual

More documents

Recommendations

Info

Section 7 Frame Modifications When reducing the wheelbase, we recommend that the suspension be moved forward and relocated on the original rail. The rail behind the suspension can then be cut to achieve the desired frame cutoff. See Figure 7–3. WARNING! Do not drill new holes any closer than 2 inches (50 mm) to existing holes. Frame drilling affects the strength of the rails. Failure to comply may result in personal injury, death, equipment or property damage. Before the rear suspension is relocated, check the new location of the spring hanger brackets. The new holes for the spring hanger brackets must not overlap existing holes and should not come any closer than 2 inches (50 mm) to existing holes. Mount the suspension Brackets On the Original Rail (see frame insert section & Figures 7-1 and 7-2) Extended Wheelbase Do Not Mount the Suspension Bracket On the Added Frame Rail Original Wheelbase Relocated Rear Suspension Shortened Wheelbase Cut Frame at Rear to Obtain Desired Cutoff FIGURE 7-3. Comparison of Original, Shortened, and Extended Wheelbases. 12/09 7-4
Section 7 Frame Modifications CROSSMEMBERS After changing a wheelbase, an additional crossmember may be required to maintain the original frame strength. The maximum allowable distance between adjacent crossmembers is 60 inches (1524 mm). If the distance between adjacent crossmembers exceeds this dimension, add a crossmember between them. See Figure 7–4. Less Than 60” Before Wheelbase is Lengthened Greater Than 60” Additional Crossmember FIGURE 7-4. Crossmember Added When Distance Exceeds 60 Inches (1524 mm) 7-5 12/09
Page 1 and 2:
2010 Kenworth T440/T470 Body Builde
Page 3 and 4:
T470/T440 Body Builder Manual Conte
Page 5 and 6:
Figures FIGURE 2-1: INCOMPLETE VEHI
Page 7 and 8:
Tables TABLE 3-1: ABBREVIATIONS USE
Page 9 and 10:
Section 2 Safety & Compliance SAFET
Page 11 and 12:
Section 2 Safety & Compliance These
Page 13 and 14:
Section 2 Safety & Compliance • N
Page 15 and 16:
Section 2 Safety & Compliance FIGUR
Page 17 and 18:
Section 3 Dimensions DIMENSIONS Thi
Page 19 and 20:
Section 3 Dimensions Prospector Tur
Page 21 and 22:
Section 3 Dimensions OVERALL DIMENS
Page 23 and 24:
Section 3 Dimensions T440 DAYCAB Th
Page 25 and 26:
Section 3 Dimensions T470 FIXED GRI
Page 27 and 28:
Section 3 Dimensions EXTENDED DAY C
Page 29 and 30:
Section 3 Dimensions Reyco 79KB 26K
Page 31 and 32:
Section 3 Dimensions KENWORTH AG 38
Page 33 and 34:
Section 3 Dimensions KENWORTH AG 40
Page 35 and 36:
Section 3 Dimensions REYCO 79KB SIN
Page 37 and 38:
Section 3 Dimensions NEWAY AD 123 S
Page 39 and 40:
Section 3 Dimensions HENDRICKSON PR
Page 41 and 42:
Section 3 Dimensions HENDRICKSON HM
Page 43 and 44:
Section 3 Dimensions CHALMERS 856-4
Page 45 and 46:
Section 3 Dimensions Watson & Chali
Page 47 and 48:
Section 3 Dimensions A B TABLE 3-19
Page 49 and 50:
Section 3 Dimensions PTO CLEARANCES
Page 51 and 52:
Section 4 Exhaust & Aftertreatment
Page 53 and 54:
Section 4 Exhaust & Aftertreatment
Page 55 and 56: Section 4 Exhaust & Aftertreatment
Page 71 and 72: Section 5 Frame Layouts FRAME LAYOU
Page 73 and 74: Section 5 Frame Layouts FIGURE 5-1.
Page 75 and 76: Section 5 Frame Layouts D6 is used
Page 77 and 78: Section 5 Frame Layouts S6 is used
Page 79 and 80: Section 5 Frame Layouts D2—Use wi
Page 87 and 88: Section 5 Frame Layouts D10—Use w
Page 89 and 90: Section 5 Frame Layouts S2—Use wi
Page 95 and 96: Section 6 Body Mounting FRONT FRAME
Page 97 and 98: Section 6 Body Mounting Note: Be su
Page 99 and 100: Section 6 Body Mounting MOUNTING HO
Page 101 and 102: Section 6 Body Mounting Frame Rail
Page 103 and 104: Section 7 Frame Modifications FRAME
Page 105: Section 7 Frame Modifications WELDE
Page 109 and 110: Section 7 Frame Modifications TORQU
Page 111 and 112: Section 9 Routing ROUTING Introduct
Page 113 and 114: Section 9 Routing Wires Crossing ot
Page 115 and 116: Appendix A Vehicle Identification V
Page 117 and 118: Appendix A Vehicle Identification N
Page 119 and 120: Appendix A Vehicle Identification T
show all

2010 Kenworth T440/T470 Body Builder Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?