2010 Kenworth T440/T470 Body Builder Manual

More documents

Recommendations

Info

Section 3 Dimensions REAR SUSPENSION LAYOUTS The rear suspension layouts are provided as a tool to help layout bodies prior to arrival. Be sure to check the axle spacing that is shown, as alternate spacings may exist and could change some of the dimensions. The dimensions shown below are the most typical installations, in special cases some hole locations will move. If you are planning on using the holes shown for your body installation, please confirm with your local KW dealer that the drawing below will be the installation used on your specific truck. Ensure that proper torque is used to reinstall any suspension components. See Tables 5-1 and 5-2 on page 5-7. It would be a good idea in this case to order the frame layout of your chassis along with your truck order. This can be done on any Kenworth truck, and will be provided 4 weeks ahead of the build schedule. If there are hole locations that are not detailed please work with your local Kenworth Dealer to request that information. Additionally optional axle spacings are shown in the charts, if you would like details on the frame drilling with optional spacings, please contact your local Kenworth dealer. 12/09 3-14
Section 3 Dimensions KENWORTH AG 380 TANDEM SUSPENSION Shown with a 52” Axle Spacing Kenworth AG 380 Suspension Data TABLE 3-5. Rear Suspension Options Suspension Type Rating Axle Spacing Laden Ride Height Unladen Ride Height AG 380 38K 52” 8.5” 8.5” 3-15 12/09
Page 1 and 2: 2010 Kenworth T440/T470 Body Builde
Page 3 and 4: T470/T440 Body Builder Manual Conte
Page 5 and 6: Figures FIGURE 2-1: INCOMPLETE VEHI
Page 7 and 8: Tables TABLE 3-1: ABBREVIATIONS USE
Page 9 and 10: Section 2 Safety & Compliance SAFET
Page 11 and 12: Section 2 Safety & Compliance These
Page 13 and 14: Section 2 Safety & Compliance • N
Page 15 and 16: Section 2 Safety & Compliance FIGUR
Page 17 and 18: Section 3 Dimensions DIMENSIONS Thi
Page 19 and 20: Section 3 Dimensions Prospector Tur
Page 21 and 22: Section 3 Dimensions OVERALL DIMENS
Page 23 and 24: Section 3 Dimensions T440 DAYCAB Th
Page 25 and 26: Section 3 Dimensions T470 FIXED GRI
Page 27 and 28: Section 3 Dimensions EXTENDED DAY C
Page 29: Section 3 Dimensions Reyco 79KB 26K
Page 33 and 34: Section 3 Dimensions KENWORTH AG 40
Page 35 and 36: Section 3 Dimensions REYCO 79KB SIN
Page 37 and 38: Section 3 Dimensions NEWAY AD 123 S
Page 39 and 40: Section 3 Dimensions HENDRICKSON PR
Page 41 and 42: Section 3 Dimensions HENDRICKSON HM
Page 43 and 44: Section 3 Dimensions CHALMERS 856-4
Page 45 and 46: Section 3 Dimensions Watson & Chali
Page 47 and 48: Section 3 Dimensions A B TABLE 3-19
Page 49 and 50: Section 3 Dimensions PTO CLEARANCES
Page 51 and 52: Section 4 Exhaust & Aftertreatment
Page 71 and 72: Section 5 Frame Layouts FRAME LAYOU
Page 73 and 74: Section 5 Frame Layouts FIGURE 5-1.
Page 75 and 76: Section 5 Frame Layouts D6 is used
Page 77 and 78: Section 5 Frame Layouts S6 is used
Page 79 and 80: Section 5 Frame Layouts D2—Use wi
Page 81 and 82:
Section 5 Frame Layouts D4—Use wi
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Section 5 Frame Layouts D10—Use w
Page 89 and 90:
Section 5 Frame Layouts S2—Use wi
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Section 6 Body Mounting FRONT FRAME
Page 97 and 98:
Section 6 Body Mounting Note: Be su
Page 99 and 100:
Section 6 Body Mounting MOUNTING HO
Page 101 and 102:
Section 6 Body Mounting Frame Rail
Page 103 and 104:
Section 7 Frame Modifications FRAME
Page 105 and 106:
Section 7 Frame Modifications WELDE
Page 107 and 108:
Section 7 Frame Modifications CROSS
Page 109 and 110:
Section 7 Frame Modifications TORQU
Page 111 and 112:
Section 9 Routing ROUTING Introduct
Page 113 and 114:
Section 9 Routing Wires Crossing ot
Page 115 and 116:
Appendix A Vehicle Identification V
Page 117 and 118:
Appendix A Vehicle Identification N
Page 119 and 120:
Appendix A Vehicle Identification T
show all

2010 Kenworth T440/T470 Body Builder Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?