2010 Kenworth T440/T470 Body Builder Manual

More documents

Recommendations

Info

Section 2 Safety & Compliance Air Intake System The following are highlights of some of the more common or critical aspects of this system. • The air intake screen may not be blocked, either fully or partially • Modifi cation to the air intake system may not restrict airfl ow. For example, pipe diameter may not be reduced • All sensors must be retained in existing locations • To retain system seal, proper clamp torque must be used. Refer to service manual for proper clamp torque Charge Air Cooler System The following are highlights of some of the more common or critical aspects of this system. • The Charge Air Cooler may not be modifi ed • The installation of engine overspeed shutdown devices must not introduce restriction in the intake system • All plumbing associated with the charge air cooler may not be modified 12/09 2-8
Section 3 Dimensions DIMENSIONS This section has been designed to provide enough information to successfully layout chassis in the body planning process. Optional equipment may not be depicted. Please contact your local Kenworth dealer if more dimensional information is desired. ABBREVIATIONS Throughout this section, and in other sections as well, abbreviations are used to describe certain characteristics on your vehicle. The chart below lists the abbreviated terms used. TABLE 3-1. Abbreviations Used AF CA EOF FS RS WB SOC BOC AFTER FRAME – FRAME RAIL OVERHANG BEHIND REAR AXLE OR MEASURED FROM CENTERLINE OF TANDEM BACK OF CAB TO CENTERLINE OF REAR AXLE OR CENTERLINE OF TANDEMS ON TANDEM SUSPENSION FRAME RAIL OVERHANG BEHIND REAR AXLE – MEASURED FROM THE CENTERLINE OF TANDEMS FRONT SUSPENSION HEIGHT REAR SUSPENSION HEIGHT WHEELBASE SIDE OF CAB BACK OF CAB TURNING RADIUS Approximate turning radius specifications are listed in the following tables as a general guide. It is important to note that optional components may alter the results. TABLE 3-2. Turning Radius Model Steering Gear Front Axle Front Wheel Front Tire T440/T470 Single TAS 65 Dana Spicer E-1202I 12K Accuride 28487 22.5 X 8.25 Bridgestone R287 295/75R22.5 Rear Suspension Tandem 52” Axle Spacing Est Curb to Wheel Base Curb Turning Radius (ft) 181 28 193 29.5 201 30.5 213 32 220 33 232 34.5 240 35.5 252 37 260 38 272 39.5 280 40.5 291 42 303 43.5 323 46 331 47 TABLE 3-2 CONTINUES ON NEXT PAGE… 3-1 12/09
Page 1 and 2: 2010 Kenworth T440/T470 Body Builde
Page 3 and 4: T470/T440 Body Builder Manual Conte
Page 5 and 6: Figures FIGURE 2-1: INCOMPLETE VEHI
Page 7 and 8: Tables TABLE 3-1: ABBREVIATIONS USE
Page 9 and 10: Section 2 Safety & Compliance SAFET
Page 11 and 12: Section 2 Safety & Compliance These
Page 13 and 14: Section 2 Safety & Compliance • N
Page 15: Section 2 Safety & Compliance FIGUR
Page 19 and 20: Section 3 Dimensions Prospector Tur
Page 21 and 22: Section 3 Dimensions OVERALL DIMENS
Page 23 and 24: Section 3 Dimensions T440 DAYCAB Th
Page 25 and 26: Section 3 Dimensions T470 FIXED GRI
Page 27 and 28: Section 3 Dimensions EXTENDED DAY C
Page 29 and 30: Section 3 Dimensions Reyco 79KB 26K
Page 31 and 32: Section 3 Dimensions KENWORTH AG 38
Page 33 and 34: Section 3 Dimensions KENWORTH AG 40
Page 35 and 36: Section 3 Dimensions REYCO 79KB SIN
Page 37 and 38: Section 3 Dimensions NEWAY AD 123 S
Page 39 and 40: Section 3 Dimensions HENDRICKSON PR
Page 41 and 42: Section 3 Dimensions HENDRICKSON HM
Page 43 and 44: Section 3 Dimensions CHALMERS 856-4
Page 45 and 46: Section 3 Dimensions Watson & Chali
Page 47 and 48: Section 3 Dimensions A B TABLE 3-19
Page 49 and 50: Section 3 Dimensions PTO CLEARANCES
Page 51 and 52: Section 4 Exhaust & Aftertreatment
Page 67 and 68:
Section 4 Exhaust & Aftertreatment
Page 69 and 70:
Section 4 Exhaust & Aftertreatment
Page 71 and 72:
Section 5 Frame Layouts FRAME LAYOU
Page 73 and 74:
Section 5 Frame Layouts FIGURE 5-1.
Page 75 and 76:
Section 5 Frame Layouts D6 is used
Page 77 and 78:
Section 5 Frame Layouts S6 is used
Page 79 and 80:
Section 5 Frame Layouts D2—Use wi
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Section 5 Frame Layouts D10—Use w
Page 89 and 90:
Section 5 Frame Layouts S2—Use wi
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Section 6 Body Mounting FRONT FRAME
Page 97 and 98:
Section 6 Body Mounting Note: Be su
Page 99 and 100:
Section 6 Body Mounting MOUNTING HO
Page 101 and 102:
Section 6 Body Mounting Frame Rail
Page 103 and 104:
Section 7 Frame Modifications FRAME
Page 105 and 106:
Section 7 Frame Modifications WELDE
Page 107 and 108:
Section 7 Frame Modifications CROSS
Page 109 and 110:
Section 7 Frame Modifications TORQU
Page 111 and 112:
Section 9 Routing ROUTING Introduct
Page 113 and 114:
Section 9 Routing Wires Crossing ot
Page 115 and 116:
Appendix A Vehicle Identification V
Page 117 and 118:
Appendix A Vehicle Identification N
Page 119 and 120:
Appendix A Vehicle Identification T
show all

2010 Kenworth T440/T470 Body Builder Manual

Create successful ePaper yourself

Delete template?

Save as template?