Logitech Ltd IU30 Impregnation Unit Operation and Maintenance ...

More documents

Recommendations

Info

Maintenance A652–01–880 Issue S 5.12.7 The pumping speed is poor � The connecting pipelines are too small in diameter � The connecting pipelines are too long � The inlet-filter is blocked. 5.12.8 There is an external oil leak � The outer shaft-seal is worn or damaged � The oil-box gaskets have deteriorated � There is an oil leak from the gas-ballast control � There is an oil leak from the drain-plug � There is an oil leak from the sight-glass Page 40 © Edwards Limited 2007. All rights reserved. Edwards and the Edwards logo are trade marks of Edwards Limited.
6 Storage and disposal 6.1 Storage CAUTION A652–01–880 Issue S Observe the storage temperature limits stated in Section 2.1. Storage below -30°C will permanently damage the pump seals. Note: If you will store a new pump in conditions of high humidity, remove the pump from its cardboard packaging box; dispose of the box (refer to Section 6.2). Use the following procedure to store the pump: 1. Shut-down the pump as described in Section 4.8. 2. Disconnect the pump from the electrical supply. 3. Purge your vacuum system and the pump with dry nitrogen and disconnect the pump from your vacuum system. 4. Replace the oil as described in Section 5.4. 5. Place and secure protective covers over the inlet and outlet-ports. 6. Store the pump in cool, dry conditions until required for use. When required, prepare and install the pump as described in Section 3. If the pump has been stored for more than a year, before you install the pump you must clean and overhaul it as described in the instructions supplied with the clean and overhaul kit. 6.2 Disposal Dispose of the pump and any components removed from it safely in accordance with all local and national safety and environmental requirements. Take particular care with components and waste oil which have been contaminated with dangerous process substances. Do not incinerate fluoroelastomer seals and ‘O’ rings. © Edwards Limited 2007. All rights reserved. Page 41 Edwards and the Edwards logo are trade marks of Edwards Limited. Storage and disposal
Page 1 and 2:
Logitech Ltd IU30 Impregnation Unit
Page 3 and 4:
Safety Precaution Sheet Logitech Va
Page 5 and 6:
hereby declare that: Equipment: Vac
Page 7 and 8:
Figure 1: Overview of the IU30 Impr
Page 9 and 10:
2. Installation 2.1 Unpacking Instr
Page 11 and 12:
d) The system should be situated aw
Page 13 and 14:
tall enough for the resin to comple
Page 15 and 16:
3.2.2. Evacuating the Resin a) When
Page 17 and 18:
4. Maintenance 4.1 General Little m
Page 19 and 20:
Appendix A Logitech Ltd, IU30 Impre
Page 21 and 22:
Material Safety Data Sheet EPOXYPAC
Page 23 and 24:
Material Safety Data Sheet EPOXYPAC
Page 25 and 26:
Material Safety Data Sheet EPOXY PA
Page 27 and 28:
Material Safety Data Sheet Date pre
Page 29 and 30:
Material Safety Data Sheet EPOXY PA
Page 31 and 32:
Material Safety Data Sheet Date pre
Page 33 and 34: Material Safety Data Sheet Date pre
Page 39 and 40: Instruction Manual RV3, RV5, RV8 an
Page 41 and 42: ITR 20439 Contents A652-01-880 Issu
Page 43 and 44: A652-01-880 Issue S 7 Service and s
Page 45 and 46: 1 Introduction 1.1 Scope and defini
Page 47 and 48: 1. Electrical inlet-connector 2. Vo
Page 49 and 50: 1.4.2 Gas-ballast control A652-01-8
Page 51 and 52: 2 Technical data A652-01-880 Issue
Page 53 and 54: © Edwards Limited 2007. All rights
Page 55 and 56: 2.2.2 Performance characteristics N
Page 57 and 58: 1. On-off switch (single-phase pump
Page 59 and 60: 2.7 Electrical data: three-phase pu
Page 61 and 62: 3 Installation 3.1 Safety WARNING A
Page 63 and 64: 3.6 Fit the motor (bareshaft pumps
Page 65 and 66: Figure 4 - Motor voltage configurat
Page 67 and 68: Figure 5 - Three-phase electrical c
Page 69 and 70: In any of the following circumstanc
Page 71 and 72: 4 Operation 4.1 ATEX directive impl
Page 73 and 74: 4.2.2 Mode selector A652-01-880 Iss
Page 75 and 76: 4.5 To pump condensable vapours A65
Page 77 and 78: 5 Maintenance 5.1 Safety informatio
Page 79 and 80: 5.4 Replace the oil A652-01-880 Iss
Page 81 and 82: 5.7 Clean the oil-level sight-glass
Page 83: A652-01-880 Issue S 5.12.3 The pump
Page 87 and 88: 7 Service and spares 7.1 Introducti
Page 89 and 90: 7.4 Accessories 7.4.1 Introduction
Page 91 and 92: 1. Inlet catchpot 2. Inlet dust fil
Page 93 and 94: 8 PFPE-prepared RV pumps 8.1 Summar
Page 95 and 96: 9 Bareshaft RV pumps 9.1 Descriptio
show all

Logitech Ltd IU30 Impregnation Unit Operation and Maintenance ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?