- Page 1 and 2:
Industrial seal self study guide Ma
- Page 3 and 4:
CHAPTER 1— INTRODUCTION This book
- Page 5 and 6:
INTRODUCTION (cont.) The Total Bear
- Page 7 and 8:
BASIC SEAL TYPES (cont.) A As a sha
- Page 9 and 10:
BASIC SEAL TYPES (cont.) As was ear
- Page 11 and 12:
CHAPTER 2 REVIEW To take this test,
- Page 13 and 14:
HM14 SKF’s non-spring loaded desi
- Page 15 and 16:
SEAL DESIGN GROUPS (cont.) Hydrodyn
- Page 17 and 18:
SEAL DESIGN GROUPS (cont.) CRWA5, C
- Page 19 and 20:
SEAL DESIGN GROUPS (cont.) HDSB HDS
- Page 21 and 22:
SEAL DESIGN GROUPS (cont.) All HS s
- Page 23 and 24:
SEAL DESIGN GROUPS (cont.) HSF SBF
- Page 25 and 26:
SEAL DESIGN GROUPS (cont.) VR2 VR2
- Page 27 and 28:
SEAL DESIGN GROUPS (cont.) Scotseal
- Page 29 and 30:
SEAL DESIGN GROUPS (cont.) “OLD
- Page 31 and 32:
CHAPTER 3 REVIEW (cont.) 30 7. The
- Page 33 and 34:
V-Ring excludes contaminants, preve
- Page 35 and 36:
Seal Applications (cont.) An effect
- Page 37 and 38:
Seal Applications (cont.) Identific
- Page 39 and 40:
Seal Applications (cont.) Substitut
- Page 41 and 42:
Seal Applications (cont.) + Handles
- Page 43 and 44:
Seal Applications (cont.) °C °F 2
- Page 45 and 46:
Chapter 4 Review To take this test,
- Page 47 and 48:
Chapter 5—Seal Selection The firs
- Page 49 and 50:
Seal Selection (cont.) l A B Seal S
- Page 51 and 52:
Seal Selection (cont.) A longer lip
- Page 53 and 54:
Chapter 5 Review (cont.) 7. Substit
- Page 55 and 56:
Wear Sleeves (cont.) Speedi-Sleeve
- Page 57 and 58:
Wear Sleeves (cont.) 8. Drop the Sp
- Page 59 and 60:
Chapter 6 Review To take this test,
- Page 61 and 62:
fig. 7A Shaft surfaces must be smoo
- Page 63 and 64: Shaft and Bore Conditions (cont.) S
- Page 65 and 66: Shaft and Bore Conditions (cont.) B
- Page 67 and 68: Chapter 7 Review (cont.) 6. Spiral
- Page 69 and 70: Installation (cont.) For best resul
- Page 71 and 72: Installation (cont.) 8. Check seal
- Page 73 and 74: Installation (cont.) Corrective Act
- Page 75 and 76: Installation (cont.) Split Seal Con
- Page 77 and 78: Chapter 8 Review To take this test,
- Page 79 and 80: Chapter 9—Troubleshooting Prelimi
- Page 81 and 82: Troubleshooting (cont...) Causes Su
- Page 83 and 84: Troubleshooting (cont...) Out-of-Ro
- Page 85 and 86: Troubleshooting (cont...) Pressure
- Page 87 and 88: Chapter 9 Review (cont...) 8. Garte
- Page 89 and 90: Glossary of Seal Terms (cont...) Di
- Page 91 and 92: Glossary of Seal Terms (cont...) MP
- Page 93 and 94: Glossary of Seal Terms (cont...) Sh
- Page 95 and 96: Final Exam Congratulations. You hav
- Page 97 and 98: 12. A cocked seal can cause a seal
- Page 99 and 100: 26. In _________________ installati
- Page 101 and 102: 40. A sealing lip that is cut, turn
- Page 103 and 104: 54. If a shaft is lightly grooved b
- Page 105 and 106: 73. More bearings fail from the ent
- Page 107 and 108: 96. Ferrous and other commonly used
- Page 109 and 110: Fold Here Fold Here PLACE STAMP HER
- Page 111 and 112: 110 NOTES
- Page 113: 112 NOTES
Change language