You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
V E C T O R O W N E R ’ S M A N U A L<br />
APPENDIX A: SIZING YOUR VECTOR 3<br />
This chart was designed to give you an idea which main and reserve canopies are compatible with<br />
one another in the Vector 3 harness/container system. If you already have a preference for a certain<br />
main and reserve canopy, then check the known pack volume in the canopy sizing table and<br />
determine if they will fit in the same container. If not, then another main or reserve must be selected.<br />
WIDTH A:<br />
The width of the backpad at the top of the container. Measured from the outside edge of the<br />
binding tape to the outside edge of the binding tape.<br />
WIDTH B:<br />
The width of the backpad at the bottom of the container. Measured from the outside edge of the<br />
binding tape to the opposite outside edge of the binding tape.<br />
LENGTH:<br />
The length of the backpad from the outside edge of the binding tape at the bottom of the container<br />
to the outside edge of the binding tape at the top of the container (the yoke). For <strong>Micron</strong>s, the<br />
length measure is calculated by adding the reserve container length to the main container length.<br />
THICKNESS:<br />
Measured from the bottom inside corner of the main container up the bottom wall to the upper<br />
end of the bound box.<br />
note<br />
If the Vector 3<br />
harness is too small<br />
or too large for the<br />
jumper’s body size,<br />
the safety of the<br />
jumper can be<br />
affected during the<br />
parachute jump. If<br />
there is any doubt<br />
as to the sizing,<br />
contact Relative<br />
W o r k s h o p<br />
immediately.<br />
APPENDIX B: CANOPY SIZING CHART<br />
The pack volume represented by these sample groups should be considered maximum<br />
recommended pack volumes to ensure proper fit, function and ease of packing. Down sizing main<br />
and/or reserve canopy one size category is acceptable. It is not recommended to use larger reserve<br />
canopies than represented in the sample group. This will compromise the functionality of the<br />
system. It is possible to temporarily use a main canopy one size larger than the recommended<br />
sample group. However this is not recommended for cosmetic and packing reasons.<br />
The sizing chart should serve as a reference only when determining which Vector 3 container will<br />
best fit your canopies. Many factors influence a canopy’s pack volume in the Vector 3 including<br />
humidity, temperature, color of fabric, experience of the packer as well as the date when the canopy<br />
was manufactured.<br />
note<br />
All dimensions<br />
given are<br />
approximate.<br />
Most canopy recommendations are determined by actually packing the canopy into the specified<br />
container by Relative Workshop. Canopy types included in this chart are intended to represent a<br />
group of common canopies suitable for each container size. Any canopy type with similar pack<br />
volume as the sample grouped will naturally be suitable for the same container. Brands appearing<br />
in this chart are in no particular way more suitable for our Vector containers than brands that are<br />
not listed.<br />
Please contact Relative Workshop at rws@relativeworkshop.com to inquire about a canopy that<br />
may not be listed here or if you have any other questions about sizing your rig. Relative Workshop<br />
encourages customer feedback; so if you feel that a canopy not presently listed in the sizing chart<br />
should be included, let us know. We will be happy to add it to our chart should we find the fit is<br />
acceptable.<br />
Page • 82:88 appendix : sizing a vector 3<br />
09354 - 11/26/2003<br />
Rev 0