F9000N Manual - Fisnar.fr

More documents

Recommendations

Info

F9000N & F2004N Series Operating Manual Section 6 : Point Type & Function Reference Rev. C- Oct. 11 1. Point Menu Below is a list of functions which are found under the ENTER key. These functions are „point-type‟ functions. The values applied will occupy one memory address. 1.1. Dispense Dot Registers the current XYZR location as a Dispense point for dispensing a dot. The dispense time and wait time must be set in a previous memory address by registering a Point Dispense Setup instruction with the SETUP key. The upward motion of the tip after dispensing can be controlled by registering a Dispense End Setup instruction and / or a Z Clearance instruction in a previous memory address. Dispense End Setup and Z Clearance instructions are registered using the SETUP key. See also Section 6:3.3 Point Dispense Setup, Section 6:3.4 Dispense End Setup and Section 6:3.5 Z Clearance. 1.2. Line Start Registers the current XYZR location as a Line Start point for dispensing a line. The line speed must be set in a previous memory address by registering a Speed instruction using the SETUP key. Dispense delay times used at Line Start point can be controlled by registering a Line Dis. Setup instruction in a previous memory address. The Line Dis. Setup instruction is registered by pressing the SETUP key. See also Section 6:3.1 Line Speed and Section 6:3.2 Line Dispense Setup. - Page 62 - © 2010 Fisnar Inc.
F9000N & F2004N Series Operating Manual Section 6 : Point Type & Function Reference Rev. C- Oct. 11 1.3. Line Passing Registers the current XYZR location as a Line Passing point, this being a location on the line where the tip changes direction, such as at the corner of a rectangle. 1.4. Arc Point Registers the current XYZR location as an Arc point, this being used to dispense material along an arc or a circular path. See Section 4: Programming Example, for an example of the use of an Arc Point. 1.5. Circle Registers the current XYZR location as a Circle point in order to dispense material along a circular path. For doing that it is necessary to enter three points on the circle to be dispensed and to register them as: Line Start point (the first point), Circle point (the second point) and Line End point (the third point). 1.6. Center Centers function registers the current XYZR location as a Center point of circle in order to dispense material along a circular path. For doing that it is necessary to enter diameter, over angle and lift Z. Value. Over Angle means that after dispensing the circle, while going through an extra part of the circle defined by the Over Angle, the dispenser will be turned OFF If you want to lift the Z at the end of the dispense, input Z lift value bigger than zero. Center Diameter: 6 mm {Type the diameter of the circle} Over Angle: 45 degree {Type the angle between the 1 to 360} Z lift: 2 mm {If you want to lift the Z end of the dispense} Mode 0 (NONE) {No tool correction} 1 (Outer) {Tip draw circle on the outside of circle} 2 (Inner) {Tip draw circle on the inside of circle} - Page 63 - © 2010 Fisnar Inc.
Page 1 and 2:
F9000N & F2004N Series Operating Ma
Page 3 and 4:
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12: Axis Control General Condition F900
Page 13 and 14: F9000N & F2004N Series Operating Ma
Page 59: F9000N & F2004N Series Operating Ma
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
show all

F9000N Manual - Fisnar.fr

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?