Software application manual - VTP UP

More documents

Recommendations

Info

Chapter 4The sections below describe each of these steps in detail.4.2 Creating and Activating a ProfileA profile specifies all mass spectrometer instrument parameters as well as basic properties ofconnected devices like pumps, autosamplers, the Coulochem III detector and the A/Dconverter.The instrument profile for a typical metabolite identification study (see section 7) may includea binary pump, autosampler, Coulochem III module and mass spectrometer. The CoulochemIII module may be used to control a pre-column EC reactor cell. For a given parentcompound, a series of injections is made, each with the cell set at a different applied potential.EC oxidation or reduction products are then separated chromatographically and characterizedby mass spectrometry. The signal (current or charge) produced from the EC reactions mayalso be simultaneously monitored using the ADC.The basic steps for creating a profile that includes the Coulochem III detector and ADC are:1. From Analyst, double-click the Hardware Configuration item in the Navigation Bar.This opens Analyst’s Hardware Configuration Editor dialog.2. Click the New Profile button, to open Analyst’s Create New Hardware Profile dialog.3. Click the Add Device button.4. Add a Mass Spectrometer device to the profile, as well as any pumps, ovens,autosamplers and other devices that you may require, by selecting from the DeviceType drop list, then the Devices list and clicking OK. Refer to the Analyst programmanual for specific details on adding and setting up these devices. (The CoulochemIII module and ADC card additions are described in the next steps.)5. Add the Coulochem III detector to the profile by clicking the Add Device button andthen selecting Software Application from the Device Type drop list. HighlightSoftware Application from the Devices list and click OK. Figure 4.1 shows the CreateNew Hardware Profile dialog for a simple profile just after adding the Coulochem IIIdriver as a Software Application.20 Coulochem ® III Analyst Driver – Version 1.0User’s Manual
Creating and Modifying Acquisition MethodsFigure 4.1. Hardware Profile with Coulochem III Detector (Unconfigured)6. Highlight the Software Application text, then click the Setup Device button and select(highlight) Coulochem III Detector from the list of software applications in theSoftware Application Settings dialog, Figure 4.2.Figure 4.2. Software Applications Settings DialogCoulochem ® III Analyst Driver – Version 1.0 21User’s Manual
Page 1 and 2: Coulochem ® III Analyst ® DriverV
Page 3 and 4: WarrantyA. ESA Biosciences, Inc. (
Page 5 and 6: License AgreementESA BIOSCIENCES, I
Page 7 and 8: License AgreementBY CUSTOM OR TRADE
Page 9 and 10: Table of Contents1. Introduction...
Page 11 and 12: 1. Introduction1.1 OverviewThis man
Page 13 and 14: Introductioncursor (over the Auto Z
Page 15 and 16: 2. System Requirements and Installa
Page 17 and 18: System Requirements and Installatio
Page 19 and 20: System Requirements and Installatio
Page 21: System Requirements and Installatio
Page 24 and 25: Chapter 3Figure 3.1. Status Bar Sho
Page 26 and 27: Chapter 33.4 Configuring the Couloc
Page 29: 4. Creating and Modifying Acquisiti
Page 33 and 34: Creating and Modifying Acquisition
Page 49 and 50: 5. Basic Coulochem III Driver Funct
Page 51: Basic Coulochem III Driver Function
Page 54 and 55: Chapter 6Instructions for building
Page 56 and 57: Chapter 6Figure 6.4. Acquisition St
Page 58 and 59: Chapter 6To view the method propert
Page 60 and 61: Chapter 77.2 Assisted Ionization -
Page 62 and 63: Chapter 7LC Conditions• Column: S
Page 64 and 65: Chapter 7Oxidation at 1000 mV produ
Page 66 and 67: Chapter 7ResultsFigure 7.4 shows th
Page 68 and 69: Appendix AC:\Program Files\ESA Bios
Page 71 and 72: Appendix B: Parameter Ranges and De

Software application manual - VTP UP

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?