Software application manual - VTP UP

More documents

Recommendations

Info

Chapter 55.3 Direct Coulochem III Detector ControlThe main display surface of the Coulochem III driver provides a set of 5 buttons for directlycontrolling the Coulochem III detector. These buttons are shown in Figure 5.1 below.Figure 5.1. The Driver’s Detector Control Buttons and IndicatorsAuto Zero. Click this button to autozero the detector. “Autozeroing” adjusts the gain toproduce a zero signal. In a 2-channel setup in DC mode, the autozero is applied across bothchannels. The Auto Zero button is disabled during the pre-run, acquisition and post-run(clean cell) phases of a run.In DC mode, post-autozero stabilization can last up to 15 seconds (or more), while in Pulsemode it is nearly instantaneous. During autozero the indicator next to the Auto Zero buttonlights green.Apply Gain. Click this button in DC mode to apply the current full scale gain range to eachenabled channel. The Apply Gain button is disabled in Pulse mode. The button is alsodisabled during the pre-run, acquisition and post-run (clean cell) phases of a run.Cells On/Off. Click either of these buttons to turn the cells on or off. When on, the indicatornext to the Cells On button lights green. These buttons always remain enabled, even during arun.Apply Settings. Clicking this button sends all of the current settings (DC or pulse) to theCoulochem III detector and resets the detector to activate the new values. The Apply Settingsbutton is disabled during the pre-run, acquisition and post-run (clean cell) phases of a run.5.4 Thermal Organizer ControlIf the system is equipped with a thermal organizer, and the organizer is enabled, the ApplyTemp button (see Figure 4.10) is used to set the setpoint temperature (from the Set Tempfield) in the Coulochem III. The Apply Temp button is disabled during the pre-run,acquisition and post-run (clean cell) phases of a run.40 Coulochem ® III Analyst Driver – Version 1.0User’s Manual
Basic Coulochem III Driver FunctionsThe ST±2 indicator turns green whenever the thermal organizer’s actual temperature is within2º C of its setpoint temperature.For more on the thermal organizer, see Section 4.4.4.Coulochem ® III Analyst Driver – Version 1.0 41User’s Manual
Page 1 and 2: Coulochem ® III Analyst ® DriverV
Page 3 and 4: WarrantyA. ESA Biosciences, Inc. (
Page 5 and 6: License AgreementESA BIOSCIENCES, I
Page 7 and 8: License AgreementBY CUSTOM OR TRADE
Page 9 and 10: Table of Contents1. Introduction...
Page 11 and 12: 1. Introduction1.1 OverviewThis man
Page 13 and 14: Introductioncursor (over the Auto Z
Page 15 and 16: 2. System Requirements and Installa
Page 17 and 18: System Requirements and Installatio
Page 19 and 20: System Requirements and Installatio
Page 21: System Requirements and Installatio
Page 24 and 25: Chapter 3Figure 3.1. Status Bar Sho
Page 26 and 27: Chapter 33.4 Configuring the Couloc
Page 29 and 30: 4. Creating and Modifying Acquisiti
Page 31 and 32: Creating and Modifying Acquisition
Page 49: 5. Basic Coulochem III Driver Funct
Page 54 and 55: Chapter 6Instructions for building
Page 56 and 57: Chapter 6Figure 6.4. Acquisition St
Page 58 and 59: Chapter 6To view the method propert
Page 60 and 61: Chapter 77.2 Assisted Ionization -
Page 62 and 63: Chapter 7LC Conditions• Column: S
Page 64 and 65: Chapter 7Oxidation at 1000 mV produ
Page 66 and 67: Chapter 7ResultsFigure 7.4 shows th
Page 68 and 69: Appendix AC:\Program Files\ESA Bios
Page 71 and 72: Appendix B: Parameter Ranges and De

Software application manual - VTP UP

Create successful ePaper yourself

Delete template?

Save as template?