JW220-UM-251 - Graphtec

More documents

Recommendations

Info

7. DISASSEMBLY AND REASSEMBLY(22) Detach the carriage assembly from the slider shaft.(23) Detach the belt clamp and the Y belt together from the carriage assembly.JW220-UM-251-93707-30
7. DISASSEMBLY AND REASSEMBLYHow to reinstall the carriage assembly(1) Reattach the Y belt to the carriage assembly in the reverse order in which it was detached.Reference:If you detached the Y belt from the belt clamp, install the Y belt as shown below.Leave two notches here.Y belt clampY beltLeave three notches here.Spread a suitable quantity of glue (for rubber and plastic) to the outside of the rubber basewhen installing the belt clamp on the rubber base. Next install the Y belt clamp on the areawhere the glue was spread on the rubber base.Carriage headRubber baseSpread a suitable quantity ofthe glue here.(2) Reattach the carriage assembly to the slider shaft in the reverse order in which it wasdetached.Clean the slider shaft using IPA if the slider shaft is dirty.(3) Temporarily reattach the slider shaft to the carriage guide plate in the reverse order in which itwas detached.(4) Remove the two screws attaching the left and right platen panels, and then mount the heightadjustment jigs to the left and right platen panels using the M3L25 binding head screws asshown below.M3L25 binding head screwHeight adjustment jigMount the height adjustment jig in theright side platen panel in the same wayas shown in this photograph.JW220-UM-251-93707-31
Page 1 and 2: JW220-06SERVICE MANUALMANUAL NO. JW
Page 3 and 4: CONTENT1. INTRODUCTION ............
Page 5: 9. TROUBLESHOOTING ................
Page 12 and 13: 2. PART NAMES and FUNCTIONSRear Vie
Page 14: 3. STANDARD ACCESSOIES and OPTIONSJ
Page 22 and 23: 7. DISASSEMBLY AND REASSEMBLYHow to
Page 24 and 25: 7. DISASSEMBLY AND REASSEMBLY7.1.3
Page 26 and 27: 7. DISASSEMBLY AND REASSEMBLY(7) Re
Page 28: 7. DISASSEMBLY AND REASSEMBLY7.1.6
Page 31 and 32: 7.2.2 How to Replace the Main Board
Page 33 and 34: 7.2.4 How to Replace the Power Supp
Page 41 and 42: 7. DISASSEMBLY AND REASSEMBLY(5) De
Page 47 and 48: 7.2.13 How to Replace the Carriage
Page 49: 7. DISASSEMBLY AND REASSEMBLY(20) R
Page 53 and 54: 7. DISASSEMBLY AND REASSEMBLY(7) Re
Page 55 and 56: 7. DISASSEMBLY AND REASSEMBLY(8) De
Page 57 and 58: 7. DISASSEMBLY AND REASSEMBLY(6) Co
Page 59: 7. DISASSEMBLY AND REASSEMBLY(11) C
Page 62 and 63: 8. ELECTRICAL ADJUSTMENTS8.2 Upgrad
Page 64 and 65: 8. ELECTRICAL ADJUSTMENTS(5) Select
Page 66 and 67: 8. ELECTRICAL ADJUSTMENTS8.3.2 How
Page 68 and 69: 8. ELECTRICAL ADJUSTMENTS8.3.3 How
Page 71 and 72: 9. TROUBLESHOOTING9. TROUBLESHOOTIN
Page 73 and 74: 9. TROUBLESHOOTINGSymptom Verificat
Page 75 and 76: 9. TROUBLESHOOTINGSymptom Verificat
Page 77 and 78: 9.5 Ink Supply9. TROUBLESHOOTINGSym
Page 79 and 80: 9.7 How toDraw Ink from the Ink Car
Page 81: 9. TROUBLESHOOTING(9) Attach the pr
Page 84 and 85: 10. PARTS LISTSOuter Casing94820133
Page 86 and 87: 10. PARTS LISTSBottom Chassis171314
Page 88 and 89: 10. PARTS LISTSMain Frame51159144 1
Page 90 and 91: 10. PARTS LISTSY Drive219 171816156
Page 92 and 93: 10. PARTS LISTSCarriage813149161211
Page 94 and 95: 10. PARTS LISTSStand108511972341211
Page 96: 10. PARTS LISTS10.9 OtherStandard A

JW220-UM-251 - Graphtec

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?