- Page 1: ®Programmable HMI Indicator/Contro
- Page 4 and 5: 4.2 Front Panel Calibration. . . .
- Page 6 and 7: iv920i Installation Manual
- Page 8 and 9: • Single- and dual-channel A/D ca
- Page 10 and 11: SoftkeyContrastTestStopGoOffScreenF
- Page 12 and 13: end-of-life stage.• There is no S
- Page 14 and 15: 2.0 InstallationThis section descri
- Page 16 and 17: 2.3.3 Serial CommunicationsThe four
- Page 18 and 19: Figure 2-6. 920i Rev H CPU Board2.3
- Page 20 and 21: 1SLOT12.5 Expansion Board Configura
- Page 22 and 23: 2.8 Fuse ReplacementFuses for the u
- Page 24 and 25: 2.11 Replacement Parts and Assembly
- Page 28 and 29: 3.0 ConfigurationTo configure the 9
- Page 30 and 31: 3.1.5 Total Scale ConfigurationThe
- Page 32 and 33: 3.2.1 SCALES MenuThe SCALES menu is
- Page 34 and 35: SCALES MenuParameter Choices Descri
- Page 36 and 37: …GRADS SPLITFORMAT ZTRKBND ZRANGE
- Page 38 and 39: SCALES Menu, FORMAT Submenu, SPLIT
- Page 40 and 41: …GRADS SPLITFORMAT ZTRKBND ZRANGE
- Page 42 and 43: SCALES Menu, FORMAT Submenu, SPLIT
- Page 44 and 45: SCALES SERIAL FEATURE PFORMT SETPTS
- Page 46 and 47: SERIAL MenuParameter Choices Descri
- Page 48 and 49: 3.2.3 FEATURE MenuSCALES SERIAL FEA
- Page 50 and 51: FEATURE MenuParameter Choices Descr
- Page 52 and 53: FEATURE Menu, CONTACT SubmenuThe CO
- Page 54 and 55: FEATURE Menu, REGULAT / INDUST Subm
- Page 56 and 57: 3.2.6 DIG I/O MenuThe DIG I/O menu
- Page 58 and 59: 3.2.7 ALGOUT MenuThe ALGOUT menu is
- Page 60 and 61: 3.2.9 VERS MenuThe VERS menu can be
- Page 62 and 63: Millivolts (or Counts)Toggles betwe
- Page 64 and 65: 4. Remove all weights from the scal
- Page 66 and 67: 5.4 Configuring ScalesOnce the hard
- Page 68 and 69: 6.0 Print FormattingThe 920i provid
- Page 70 and 71: Command Description Supported Ticke
- Page 72 and 73: 6.4.2 Using the Front PanelIf you h
- Page 74 and 75: 7.0 Truck ModesThe truck in/out mod
- Page 76 and 77:
8.0 SetpointsThe 920i indicator pro
- Page 78 and 79:
Kind Description Batch ContinuousCO
- Page 80 and 81:
AGROSS NET -GROSS -NET ACCUMROCSame
- Page 82 and 83:
CPAUSE and COUNTER setpointsVALUEAC
- Page 84 and 85:
EDIGIN, AVG, and TOD setpointsDIN S
- Page 86 and 87:
GPLSCNTVALUESOURCECOASTBATCHPSHPRNT
- Page 88 and 89:
SETPTS MenuParameter Choices Descri
- Page 90 and 91:
SETPTS MenuTOLBAND 00-9999999TOLCNT
- Page 92 and 93:
8.3 Batch OperationsSoftkeys can be
- Page 94 and 95:
Setpoint 3 uses DIGOUT 1 to fill a
- Page 96 and 97:
9.1.2 Reporting CommandsReporting c
- Page 98 and 99:
Command Description ValuesSC.ROC.RE
- Page 100 and 101:
Command Description ValuesSK#1-SK#3
- Page 102 and 103:
Command Description ValuesSP.DACCEP
- Page 104 and 105:
9.1.5 Normal Mode CommandsThe norma
- Page 106 and 107:
Example. The following commands pla
- Page 108 and 109:
creates a visible, 1.5" x 1.5" (120
- Page 110 and 111:
SymbolStyle (x)DescriptionWidget St
- Page 112 and 113:
10.0 Appendix10.1 TroubleshootingTa
- Page 114 and 115:
5. Start iRev 4 and enter monitor m
- Page 116 and 117:
REGULAT / INDUST ParameterREGULAT M
- Page 118 and 119:
10.6 Custom Stream FormattingEach p
- Page 120 and 121:
Format Identifier Defined By Descri
- Page 122 and 123:
10.7.2 Cardinal 738 IndicatorSample
- Page 124 and 125:
10.8 Data FormatsContinuous Output
- Page 126 and 127:
10.10 Conversion Factors for Second
- Page 128 and 129:
10.12 Dimension Drawings12.50"10.56
- Page 130 and 131:
10.38"BACK VIEW11.56"5.20"9.16"7.95
- Page 132 and 133:
10.13 Printed InformationSystem Man
- Page 134:
920i Limited WarrantyRice Lake Weig