920i Installation Manual V4.01 - Rice Lake Weighing Systems

More documents

Recommendations

Info

SCALES SERIAL FEATURE PFORMT SETPTS DIG I/O VERSPORT 3…PROGINCMDSCALE IND SC DISPLAYIQUBE2See PROGIN SelectionsSee iQUBE2InstallationManual ,PN 106113BAUDBITSTERMINSTOP BITSECHORESPONSEEOLDLYHANDSHK9600192008NONE7EVENCR/LFCR21ONOFFONOFF0numberOFFXONXOFF288007ODD38400576008ODD8EVEN115200300600120024004800STREAMSOURCESFMTSFMTTOKENSOFFLFTINDUST4KEYSKEYPADDISPLAYList ofconfiguredscalesIf STREAM ≠ OFFformatformatIf PORT =SCALE or IND SCPRIMAR…TARESelectable token charactersIf STREAM = LFT or INDUSTIf PORT =CMD or PROGINFigure 3-9. SERIAL Menu, Port 338 920i Installation Manual
SCALES SERIAL FEATURE PFORMT SETPTS DIG I/O VERSPORT 4…PROGINCMDSCALE IND SC DISPLAYIQUBE2See PROGIN SelectionsSee iQUBE2InstallationManual ,PN 106113BAUDBITSTERMINSTOP BITSECHORESPONSEEOLDLYHANDSHK9600192008NONE7EVENCR/LFCR21ONOFFONOFF0numberOFFXONXOFF288007ODD38400576008ODD8EVEN115200300600PORTTYPEDUPLEXADDRESS120024004800232485422HALF0FULLnumberIf PORTTYPE = 485STREAMSOURCESFMTSFMTTOKENSOFFLFTINDUST4KEYSKEYPADDISPLAYList ofconfiguredscalesIf STREAM ≠ OFFformatformatIf PORT =SCALE or IND SCPRIMAR…TARESelectable token charactersIf STREAM = LFT or INDUSTIf PORT =CMD or PROGINFigure 3-10. SERIAL Menu, Port 4 and Expansion PortsConfiguration 39
Page 1: ®Programmable HMI Indicator/Contro
Page 4 and 5: 4.2 Front Panel Calibration. . . .
Page 6 and 7: iv920i Installation Manual
Page 8 and 9: • Single- and dual-channel A/D ca
Page 10 and 11: SoftkeyContrastTestStopGoOffScreenF
Page 12 and 13: end-of-life stage.• There is no S
Page 14 and 15: 2.0 InstallationThis section descri
Page 16 and 17: 2.3.3 Serial CommunicationsThe four
Page 18 and 19: Figure 2-6. 920i Rev H CPU Board2.3
Page 20 and 21: 1SLOT12.5 Expansion Board Configura
Page 22 and 23: 2.8 Fuse ReplacementFuses for the u
Page 24 and 25: 2.11 Replacement Parts and Assembly
Page 26 and 27: 282918/12X/E17/4X/BCFGA14/11X/A4111
Page 28 and 29: 3.0 ConfigurationTo configure the 9
Page 30 and 31: 3.1.5 Total Scale ConfigurationThe
Page 32 and 33: 3.2.1 SCALES MenuThe SCALES menu is
Page 34 and 35: SCALES MenuParameter Choices Descri
Page 36 and 37: …GRADS SPLITFORMAT ZTRKBND ZRANGE
Page 38 and 39: SCALES Menu, FORMAT Submenu, SPLIT
Page 40 and 41: …GRADS SPLITFORMAT ZTRKBND ZRANGE
Page 42 and 43: SCALES Menu, FORMAT Submenu, SPLIT
Page 46 and 47: SERIAL MenuParameter Choices Descri
Page 48 and 49: 3.2.3 FEATURE MenuSCALES SERIAL FEA
Page 50 and 51: FEATURE MenuParameter Choices Descr
Page 52 and 53: FEATURE Menu, CONTACT SubmenuThe CO
Page 54 and 55: FEATURE Menu, REGULAT / INDUST Subm
Page 56 and 57: 3.2.6 DIG I/O MenuThe DIG I/O menu
Page 58 and 59: 3.2.7 ALGOUT MenuThe ALGOUT menu is
Page 60 and 61: 3.2.9 VERS MenuThe VERS menu can be
Page 62 and 63: Millivolts (or Counts)Toggles betwe
Page 64 and 65: 4. Remove all weights from the scal
Page 66 and 67: 5.4 Configuring ScalesOnce the hard
Page 68 and 69: 6.0 Print FormattingThe 920i provid
Page 70 and 71: Command Description Supported Ticke
Page 72 and 73: 6.4.2 Using the Front PanelIf you h
Page 74 and 75: 7.0 Truck ModesThe truck in/out mod
Page 76 and 77: 8.0 SetpointsThe 920i indicator pro
Page 78 and 79: Kind Description Batch ContinuousCO
Page 80 and 81: AGROSS NET -GROSS -NET ACCUMROCSame
Page 82 and 83: CPAUSE and COUNTER setpointsVALUEAC
Page 84 and 85: EDIGIN, AVG, and TOD setpointsDIN S
Page 86 and 87: GPLSCNTVALUESOURCECOASTBATCHPSHPRNT
Page 88 and 89: SETPTS MenuParameter Choices Descri
Page 90 and 91: SETPTS MenuTOLBAND 00-9999999TOLCNT
Page 92 and 93: 8.3 Batch OperationsSoftkeys can be
Page 94 and 95:
Setpoint 3 uses DIGOUT 1 to fill a
Page 96 and 97:
9.1.2 Reporting CommandsReporting c
Page 98 and 99:
Command Description ValuesSC.ROC.RE
Page 100 and 101:
Command Description ValuesSK#1-SK#3
Page 102 and 103:
Command Description ValuesSP.DACCEP
Page 104 and 105:
9.1.5 Normal Mode CommandsThe norma
Page 106 and 107:
Example. The following commands pla
Page 108 and 109:
creates a visible, 1.5" x 1.5" (120
Page 110 and 111:
SymbolStyle (x)DescriptionWidget St
Page 112 and 113:
10.0 Appendix10.1 TroubleshootingTa
Page 114 and 115:
5. Start iRev 4 and enter monitor m
Page 116 and 117:
REGULAT / INDUST ParameterREGULAT M
Page 118 and 119:
10.6 Custom Stream FormattingEach p
Page 120 and 121:
Format Identifier Defined By Descri
Page 122 and 123:
10.7.2 Cardinal 738 IndicatorSample
Page 124 and 125:
10.8 Data FormatsContinuous Output
Page 126 and 127:
10.10 Conversion Factors for Second
Page 128 and 129:
10.12 Dimension Drawings12.50"10.56
Page 130 and 131:
10.38"BACK VIEW11.56"5.20"9.16"7.95
Page 132 and 133:
10.13 Printed InformationSystem Man
Page 134:
920i Limited WarrantyRice Lake Weig
show all

920i Installation Manual V4.01 - Rice Lake Weighing Systems

Create successful ePaper yourself

Delete template?

Save as template?