ATEX compliant - SMC ETech

Series 55-CP95ISO SymbolDouble actingNote) All other specifications(dimensions, drawings, etc.)are the same as the non ATEX type.SpecificationsBore sizeATEX category 1)ActionFluidProof pressureMax. operating pressureMin. operating pressureLubricationAmbient and fluid temperatureOperating piston speedAllowable stroke toleranceCushionThread tolerancePort sizeMountingStandard StrokeBore size(mm)ø32 ø40 ø50 ø63 ø80 ø100Double actingAir (Non-lube)1.5MPa1.0MPa0.05MPaNot required (Non-lube)–10 to 60°C50 to 1000mm/s+1.0+1.4to 250: 0 , 251 to 1000: 0Both ends (Air cushion)JIS class 2G1/8 G1/4 G1/4 G3/8 G3/8 G1/2Basic, axial foot, front flange, rear flange,single rear clevis, double rear clevisStandard stroke (mm)II 2GDcNote 1) This cylinder can be used in zones 1 and 21 and in zones 2 and 22.If the cylinder is used with SMC category 3 type auto switch, then thecylinder can only be used in zones 2 and 22 and not in zones1 and 21.32 25, 50, 80, 100, 125, 160, 200, 250, 320, 400, 50040 25, 50, 80, 100, 125, 160, 200, 250, 320, 400, 50050 25, 50, 80, 100, 125, 160, 200, 250, 320, 400, 500, 60063 25, 50, 80, 100, 125, 160, 200, 250, 320, 400, 500, 60080 25, 50, 80, 100, 125, 160, 200, 250, 320, 400, 500, 600, 700, 800100 25, 50, 80, 100, 125, 160, 200, 250, 320, 400, 500, 600, 700, 800Intermediate strokes are available.95°C (T5) Ta –10 to 40°C115°C (T4) Ta 40 to 60°CMax. ∗stroke7008001200120014001500Mounting Bracket, Mounting AccessoriesDescriptionLF, GCDDSESEGKMKJJABore size ø32 ø40 ø50 ø63 ø80 ø100Foot (1)FlangeSingle rear clevisDouble rear clevisDouble rear clevis(for ES accessory)Angled rear cleviswith ball jointAngled rear clevisRod clevisPiston rod ball jointFloating jointL5032F5032C5032D5032DS5032ES5032E5032GKM10-20KJ10DJA30-10-125L5040F5040C5040D5040DS5040ES5040E5040GKM12-24KJ12DJA40-12-125L5050F5050C5050D5050DS5050ES5050Note 1) Two foot brackets required for one cylinder.Note 2) Accessories for each mounting bracket are as follows.Foot, Flange, Single clevis: Mounting boltsDouble rear clevis: (D,DS): Clevis pinNote 3) GKM according to ISO 8140Note 4) KJ according to ISO 8139Note 5) Piston rod nut is standardL5063F5063C5063D5063DS5063ES5063E5050 E5063GKM16-32 GKM16-32KJ16D KJ16DJA50-16-150 JA50-16-150L5080F5080C5080D5080DS5080ES5080L5100F5100C5100D5100DS5100ES5100E5080 E5100GKM20-40 GKM20-40KJ20D KJ20DJAH50-20-150 JAH50-20-15011