<strong>ATEX</strong> CompliantMechanically Jointed Rodless CylinderSe ries 55-MY1HHigh Precision Guide Type/ø10, ø16, ø20, ø25, ø32, ø40Bore size(mm)10, 16, 2025, 32, 40How to OrderHigh PrecisionGuide Type 55-MY1H 25Standard strokesStandard stroke(mm)50, 100, 150, 200, 300, 350,400, 450, 500, 550, 600SymbolNote) All other specifications(dimensions, drawings, etc.)are the same as the non <strong>ATEX</strong> type.<strong>ATEX</strong> category 2Maximummanufacturablestroke (mm)10001500High precisionguide typeSpecificationsBore size (mm)FluidActionOperating pressure rangeProof pressureAmbient and fluid temperatureCushionLubricationStroke length tolerancePort sizeFront/Side portsBore size10162025324010mm16mm20mm25mm32mm40mm-GPipingSymbol-TNTFStrokeRefer to thestandard stroketable below.PipingTypeM threadRcNPTGBore sizeø10~ø20ø25~ø4010 16 20 25 32 40<strong>ATEX</strong> category 1) 75°C (T6) Ta 5 to 40°CII 2Gc95°C (T5) Ta 40 to 60°COperating piston speed0.2to 0.8MPaRubberbumper100 to500 mm/sM5 x 0.8300AirDouble acting0.1 to 0.8MPa1.2MPa5 to 60°CAir cushionNon-lube+1.80100 to 1000 mm/sNote 1) This cylinder can be used in zone 1 and 2.If the cylinder is used with <strong>SMC</strong> category 3 type auto switch, then thecylinder can only be used in zone 2 and not in zone 1.For 55-MY1HWhen using an Auto switch, select the appropriate switch from the following table and order it separately.Standard typeCentralized piping typeRc, NPT, G1/8Applicable auto switch specificationsAuto switch only conforms to Category 3. (II 3GD EEx nA II T5x -10°C ≤ Ta ≤ +60°C IP67)For detailed specifications on the D-A93(V), A90(V), Z73, Z80, M9P(V) and Y7PV, please refer to the relevant pages in Best Pneumatics.(Note: Reed auto switches for AC 100V and DC 100V are not within the specification. Also for D-M9P(V) type, see D-F9P(V) type specifications.)TypeReedauto switchSolid stateauto switchø10 to ø20D-A93V-588D-A90V-588D-A93-588D-A90-588D-M9PV-588D-M9P-588Model No.ø25 to ø40D-Z73-588D-Z80-588D-Y7PV-588D-Y7P-588Electrical entryGrommet(Perpendicular entry)IndicatorYesWiring(Output)24VLoad voltageDC12VACNo24V or less2-wiring48V 48V or lessGrommet(In-line entry)GrommetYesNo24V24V or less12V48V 48V or less(Perpendicular entry)Yes 3-wiringGrommet (PNP)(In-line entry)24V 5V, 12V• Lead wire length 0.5m --- Nil (e.g.) D-A93-5883 m --- L (e.g.) D-A93L-5885 m --- Z (e.g.) D-A93Z-588Note 2) When mounting an auto switch on a 55- series (Category 2) Model,the <strong>ATEX</strong> category of the auto switch cylinder changes to Category 3,which is the same category as the auto switch.22Note 1)0.5(—)Lead wire ∗ (m)3(L)5(Z)IC circuitIC circuitIC circuitApplicableloadRc, NPT, G1/4RelayPLCsolid state auto switch is available after receiving an order.
<strong>ATEX</strong> CompliantRotary Actuator / Rack Pinion TypeSe ries 56-CRQ2Size: ø10, ø15, ø20,ø30, ø40How to OrderMethod ofdisplaying model56-CDRQ2 W 10TF90CSW<strong>ATEX</strong> category 3-DBuilt-in magnetWithoutBuilt-in magnetSingle shaft with one chamerSingle shaft with keyDouble shaftSingle shaft long, wkey & chamfersShaft typeSize10-1520-4010-1520-401015203040Bore size10mm15mm20mm30mm40mmTape of port threadSize10,1520,30,40Rotation90180Air cushionSizes Air cushion10, 15 Without -20, 30, 40Without -With C10.15 is rubber bumper80°,100°170°,190°Tape of port threadNil M5Nil Rc1/8TF G1/8TN NPT1/8TT NPTF1/8Size10 15 20 30 40Output (N·m) ∗ 0.3 0.75 1.8 3.1 5.3<strong>ATEX</strong> category<strong>ATEX</strong> categoryTemperature: 60°C (T6) Ta 0 to 40°Cindication:II 3G80°C (T5) Ta 40 to 60°CFluidAir (Non-lube)Max. operating pressure0.7 MPa1 MPaMin. operating pressure0.15 MPa0.1 MPaAmbient and fluid temperature0° to 60°C (No freezing)CushionRubber bumperNot attached, Air cushionAngle adjustmentRotation end ±5°Rotation80° to 100°, 170° to 190°Port sizeM5 x 8 Rc 1/8, G 1/8, NPT 1/8, NPTF 1/8∗ Output for an operating pressure of 0.5 MPa.23