<strong>ATEX</strong>category 2Dual rod cylinderBore size6 6mm10 10mm15 15mm20 20mm25 25mm32 32mm55-CXS W M 20 100-WML<strong>ATEX</strong> Compliant Dual Rod CylinderSeries 55-CXS/Wø6, ø10, ø15, ø20, ø25, ø32How to OrderTypeSingle rodDouble rodBearingSlide bearingBall bushing bearingSymbol-TFPort thread typeTypeM threadRcGBore sizeø6~ø20ø25~ø32ø25~ø32Standard StrokesCXSBore sizeø6ø10ø15ø20ø25ø32CXSWBore sizeø6ø10ø15ø20ø25ø32CXS SpecificationsBore size (mm)Standard stroke10, 20, 30, 40, 5010, 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 7510, 15, 20, 25, 30, 35, 40, 45,50, 60, 70, 75, 80, 90, 100Standard stroke10, 20, 30, 40, 5010, 20, 30, 40, 5010, 20, 30, 40, 50, 75, 1006 10 15Long stroke80, 90, 100, 110, 120, 125, 150110, 120, 125, 150110, 120, 125,150, 175, 200Long stroke75, 100, 125, 150125, 15, 175, 20020 25<strong>ATEX</strong> category 1) 65°C (T6) Ta –10 to 40°CII 2GDc85°C (T6) Ta 40 to 60°C32(mm)(mm)Min. operating pressure0.15MPa 0.1MPa 0.05MPa18Note) All other specifications(dimensions, drawings, etc.)are the same as the non <strong>ATEX</strong> type.Max. operating pressureProof pressureFluidAmbient and fluid temperaturePiston speedPiping portStroke adjustable rangeBearingCushionCXSW SpecificationsBore size (mm)30 to 300mm/s30 to 800mm/s0.7MPa1.05MPaAir (Non-lube)–10 to 60°C (No freezing)30 to 700mm/s30 to 600mm/sM5 Rc, G1/80 to –5 mm to the standard strokeSlide bearing, Ball bushing bearing (Same dimensions)Rubber bumper6 10 1520 25 32<strong>ATEX</strong> category 1) 65°C (T6) Ta –10 to 40°CII 2GDc85°C (T6) Ta 40 to 60°CFluidAir (Non-lube)Min. operating pressure0.15MPa0.1MPaMax. operating pressureProof pressureAmbient and fluid temperaturePiston speedPiping port0.7MPa1.05MPa–10 to 60°C (No freezing)50 to 500mm/sM5 Rc, G1/8Stroke adjustable rangeBearingCushion0 to –10mm (Extension side: 5mm, Retraction side: 5mm)Slide bearing, Ball bushing (Same dimensions)Rubber bumperNote 1) This cylinder can be used in zones 1 and 21 and in zones 2 and 22.If the cylinder is used with <strong>SMC</strong> category 3 type auto switch, then thecylinder can only be used in zones 2 and 22 and not in zones1 and 21.
<strong>ATEX</strong> Compliant Dual Rod Cylinder Series 55-CXSFor 55-CXSWhen using an Auto switch, select the appropriate switch from the following table and order it separately.Applicable auto switch specificationsAuto switch only conforms to Category 3. (II 3GD EEx nA II T5x -10°C ≤ Ta ≤ +60°C IP67)For detailed specifications on the D-Z73, Z80, Y7P, and Y7PV, please refer to the relevant pages in Best Pneumatics.(Note: Reed auto switches for AC 100V and DC 100V are not within the specification.)TypeReedauto switchSolid stateauto switchModel No.D-Z73-588D-Z80-588D-Y7P-588D-Y7PV-588Electrical entryGrommet(In-line)Grommet(In-line)Grommet(Perpendicular)IndicatorYesNoYesWiring(Output)2-wiring3-wiring(PNP)• Lead wire length 0.5m --- Nil (e.g.) D-Z73-5883 m --- L (e.g.) D-Z73L-5885 m --- Z (e.g.) D-Z73Z-588Note 2) When mounting an auto switch on a 55- series (Category 2) Model,the <strong>ATEX</strong> category of the auto switch cylinder changes to Category 3,which is the same category as the auto switch.24VDCLoad voltage12VAC24V or less 48V 48V or less24V5V,12VNote 1)0.5(—)Lead wire ∗ (m)3(L)5(Z)IC circuitIC circuitApplicableloadRelayPLCsolid state auto switch is available after receiving an order.19