IM 01F06A00-01EN 14th Edition - Yokogawa

(6) Item F: Thermometer (Only for Option Code /MV)These items is for thermometer setting when.A Value in “( )” is the data corresponding to the indicator.ItemF00F10F12F14F15F16F18F19F20F21F22F23F24F26F27F28F29F30F31F32F35F40F45F50F52F55F56F57F58F60NameTHERMOMETERFunctionDENSITY bTEMP UNITTEMP b1st coef2nd coefMASS UNITTIME UNITFLOW SPANDAMPINGTEMP DAMPINGCABLE LENGTHA/OUT SELECTWWWWWWWWWWWWData Range(Indicate and set only for F55: TEMP)TEMP 0% WTEMP 100% WTEMP ERR OUT WSELF CHECKR / WW Monitor onlySaturated Steam(0)(1)Superheat Steam (2)GAS: STD/Normal (3)LIQUID: Mass (4)Not use (5)(Indicate and set only for F10: Saturated Stem)MASS UNIT W kgt(0)(1)Ib (2)k Ib (3)(Indicate and set only for F10: Superheat Steam)PRSS UNIT WMPa abs (0)kPa abs (1)bar abs (2)kg/cm2 a (3)psia (4)PRESS fMASS UNITWW0.00001 to 32000kgt(0)(1)Ib (2)k Ib (3)(Indicate and set only for F10: GAS STD/Normal)TEMP UNIT Wdeg C (0)deg F (1)TEMP bPRESS UNITPRESS fPRESS bDEVIATIONSTD/NOR UNITWWWWWWWWWW-999.9 to 999.9MPa abskPa absbar abskg/cm2 apsia0.00001 to 320000.00001 to 320000.001 to 10.000Nm3k Nm3(0)(1)(2)(3)(4)(0)(1)M Nm3 (2)NI (3)Sm3 (4)k Sm3 (5)M Sm3 (6)SI (7)scf (8)k scf (9)M scf (10)(Indicate and set only for F10: Liquid: Mass)DENSITY UNIT WRkg/m3 (0)Ib/cf (1)Ib/USgal (2)Ib/UKgal (3)0.00001 to 32000deg C (0)deg F (1)-999.9 to 999.9-32000 to 32000-32000 to 32000kg (0)t (1)Ib (2)k Ib (3)/s (0)/m (1)/h (2)/d (3)0.00001 to 320000 to 990 to 990 to 30FLOW (0)TEMP (1)-999.9 to 999.9-999.9 to 999.90% (0)OUT LIMIT(H) (1)TEMP f (2)GOODERRORUnitF14F18F20F20F26F281/F281/F28 2FU+35secsecmD20D20Decimal Point0 to 510 to 50 to 530 to 510 to 50 to 50 to 500011RemarkMenu F (Thermometer function)Select thermometer function.(Move to F40 when “Monitor only” is selected)(Move to F60 when “Not Use” is selected)Selection of mass flow rate unitSelection of pressure unitAbsolute pressure at operating condition(Manual setting vaiue)Selection of mass flow rate unitSelection of temperature unitStandard/Normal temperatureSelection of temperture unitAbsolute pressure at operating condition(Manual setting value)Absolute pressure at Standard conditionDeviation factorSelection of volumetric unit at normal conditionN: NormalS: StandardSelection of density unitDensity of standard conditionSelection of temperature unitTemperature of standard condition1st temperature coefficient2nd temperature coefficientSelection of mass flow rate unitSelection of time unit(*1) Available for 3.10 or greater version that can be checked in K50 SOFTWARE REV.Flow spanDampingDamping for temperture outputCable length for signal cable (0m in case of integral version)Selection of analog outputTemperture value at 0%Temperture value at 100%Selection of themometer error output when “F55: TEMP”is selected (A value of OUT LIMIT(H) depend on D30)Self-diagnostic message5. PARAMETER SETUPInitial Value Disp U/D *15-6 IM 01F06A00-01EN(0)(0)(0)0.1013(0)(0)15.0(0)0.10130.10131.0(0)(0)1024(0)15.000(0)10.5440(0)-402501DDDDDDDDDDDDDDDDDDDDDDDDDDDLLLLLLLLLLLLLLLLLLLLLLLLLLLT050307.EPS