Docu Cutter DC-545 HC/DC-545 HCEX

More documents

Recommendations

Info

L8-T1080Operating Instraction - DC545 HCPart Names and Their FunctionsAdjustments○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○○Elevator level ( Feed tray)The elevator level should be adjusted in thefollowing cases.a. The machine does not feed.→ Lower the lever. The level of the elevator israised.b. The machine feeds multiple sheets at once.(double feed)→ Raise the lever. The level of the elevator islowered.Figure 1-1: Close-up of the level adjustment lever123○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○○SeparatorThe height of the separator should be adjusted inthe following cases:a. The machine does not feed.→ Turn the knob in the clockwise direction (to asmaller number). The position of the separator islowered.b. The machine feeds multiple sheets at once.(double feed)→ Turn the knob in the anti-clockwise direction (toa larger number). The position of the separator israised.Figure 1-2: Location of the level adjustment leverFigure 2-1: Close-up of the separatoradjustment knobWARNING Cutters and movable parts are inside this cover.Before opening the cover to work,unplug the power cord.Use caution when working near cuttersand movable parts.Figure 2-2: Location of the separatoradjustment knob○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○15
Part Names and Their Functions○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○○Adjusting the airflowThe amount of airflow should be adjusted in thefollowing cases:a. The machine does not feed.→ Turn the knob in the anti-clockwise direction (toa larger number). The amount of airflow isincreased.b. The machine feeds multiple sheets at once.(double feed)→ Turn the knob in the clockwise direction (to asmaller number). The amount of airflow isdecreased.Figure 3-1: Close-up of the airflow adjustmentknobFigure 3-2: Location of the airflow adjustmentknob○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○○Adjusting the amount of skewPaper may be cut at an angle if a skew in the paperarises during feeding. When this happens, correctthe problem by changing the angle of the feedguide.Figure 4-1: Skew adjustment knob○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○16
Page 6 and 7: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 8 and 9: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 10 and 11: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 12 and 13: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 14: Operating Instraction - DC545 HCPar
Page 19 and 20: Chapter 2Before Using This Machine
Page 21 and 22: How to set up the System○ ○ ○
Page 23: Part Names and Their Functionsi!0oN
Page 26 and 27: Before Using This Machine - DC545 H
Page 28 and 29: Operating Instructions - DC545 HCEX
Page 30 and 31: Operating Instructions - DC545 HCEX
Page 32 and 33: Troubleshooting - DC545 HCEXTrouble
Page 34 and 35: Troubleshooting - DC545 HCEXError M
Page 40 and 41: Troubleshooting - DC545 HCEXWhen a
Page 54 and 55: Manual Programming - DC545 HCEXChap
Page 56 and 57: Manual Programming - DC545 HCEXDefi
Page 58 and 59: Manual Programming - DC545 HCEXDefi
Page 60: Manual Programming - DC545 HCEXDefi
Page 63 and 64: Factory Preset JobsPROGRAMNUMBER #9
Page 65 and 66:
Factory Preset JobsEuropePROGRAMNUM
Page 67 and 68:
How to Manually Program a Job○
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Appendix - DC545 HC/DC545 HCEXThis
Page 75 and 76:
SpecificationsSpecifications of Reg
Page 77 and 78:
SpecificationsThe second program en
Page 79 and 80:
SpecificationsSelect OptionsDelete
Page 81 and 82:
SpecificationsPOSITIONING THE BAR C
Page 83 and 84:
Specifications2. Non-Printing AreaR
Page 85 and 86:
SpecificationsHow to do AUTO CUTWha
Page 87 and 88:
MEMO
Page 89 and 90:
MEMO
show all

Docu Cutter DC-545 HC/DC-545 HCEX

Create successful ePaper yourself

Delete template?

Save as template?