Docu Cutter DC-545 HC/DC-545 HCEX

More documents

Recommendations

Info

Appendix - DC545 HC/DC545 HCEXSpecificationsDC-545 with HCEX AUTO FEEDER SpecificationsProduct name / Model No.Input paper sizePaper sizeInput paper weightFinishing sizeLead edge trimTrail Edge TrimSide edge trimSpeedDesktop modelMin.:8.5" x 11" / A4Max.:12.6" x 18" / A3Min.:110gsmMax.:230gsm DC-545 with HCEX AUTO FEEDERMin.:2"(Width) x 3.5"(Length) Min.:0.125"(3.2mm)Min.:0.125"(3.2mm)Min.:0.125'(3.2mm)Max.:4.5"(114mm)Max : 9ppm (A4 lengthwise. 4-side trim. 1 score)Trim/Score tolerance +/- 0.03"(+/- 0.762mm)
SpecificationsSpecifications of Reg. Mark and Bar Code1.Reg. Mark Details (Vertical/Horizontal)Length: 5mm or moreWidth: 0.4mm or more2.Bar codeBar code: CODE-39Start/stop code: RequiredCheck digit: OptionalMinimum resolving power : 0.254mmFine line : Thick line : 1:2.5Bar height: 4mm or moreUnder the requirements listed above, the bar code width will be about 15mm.Printing Position: See P.62 to P.64 for details.Print the bar code data in the following sequence:q is the start code designator for CODE-39.w is the 10’s digit data of the program number.(Example: When the program number is 11 , the data is "1".)e is the 1’s digit data of the program number.(Example: When the program number is 11 , the data is "1".)1 2 3 4 5r is the check digit.t is stop code of CODE-39.These figures indicate program number, with which the machine recognizes a stored setting for certain Jobs. (start from00)72
Page 6 and 7:
○ ○ ○ ○ ○ ○ ○ ○ ○
Page 8 and 9:
○ ○ ○ ○ ○ ○ ○ ○ ○
Page 10 and 11:
○ ○ ○ ○ ○ ○ ○ ○ ○
Page 12 and 13:
○ ○ ○ ○ ○ ○ ○ ○ ○
Page 14:
Operating Instraction - DC545 HCPar
Page 17 and 18:
Part Names and Their Functions○
Page 19 and 20:
Chapter 2Before Using This Machine
Page 21 and 22:
How to set up the System○ ○ ○
Page 23: Part Names and Their Functionsi!0oN
Page 26 and 27: Before Using This Machine - DC545 H
Page 28 and 29: Operating Instructions - DC545 HCEX
Page 30 and 31: Operating Instructions - DC545 HCEX
Page 32 and 33: Troubleshooting - DC545 HCEXTrouble
Page 34 and 35: Troubleshooting - DC545 HCEXError M
Page 40 and 41: Troubleshooting - DC545 HCEXWhen a
Page 54 and 55: Manual Programming - DC545 HCEXChap
Page 56 and 57: Manual Programming - DC545 HCEXDefi
Page 58 and 59: Manual Programming - DC545 HCEXDefi
Page 60: Manual Programming - DC545 HCEXDefi
Page 63 and 64: Factory Preset JobsPROGRAMNUMBER #9
Page 65 and 66: Factory Preset JobsEuropePROGRAMNUM
Page 67 and 68: How to Manually Program a Job○
Page 73: Appendix - DC545 HC/DC545 HCEXThis
Page 77 and 78: SpecificationsThe second program en
Page 79 and 80: SpecificationsSelect OptionsDelete
Page 81 and 82: SpecificationsPOSITIONING THE BAR C
Page 83 and 84: Specifications2. Non-Printing AreaR
Page 85 and 86: SpecificationsHow to do AUTO CUTWha
Page 87 and 88: MEMO
Page 89 and 90: MEMO
show all

Docu Cutter DC-545 HC/DC-545 HCEX

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?