Docu Cutter DC-545 HC/DC-545 HCEX

More documents

Recommendations

Info

Manual Programming - DC545 HCEXChapter 5Manual Programming - DC545 HCEXThis chapter describes how to manually program the Docu Cutter.The Docu Cutter is manually programmable with 80 sets of job dimensions or program numbers. Each setof dimensions are stored and recalled by a program number. (a P.45, “Factory Preset Jobs”)Prior to Programming a Job1Before programming a job carefully measure,in millimeters, the required slits, cuts andcreases. See the Figure 1 for reference andFigure 2 for a detailed description of eachfunction.Record the values in “Customer ProgramedJobs”. Remember that all measurements,except MARK 1, are in millimeters.Familiarize yourself with the following illustrationsand instructions to make the programmingprocess easy and trouble free.IMPORTANT NOTES:There are a total of five slitters. Two slitters arefor the margins and the remaining threeslitters are for the center of the sheet.There is a guillotine cutter that performs cutsperpendicular to the line of the paper travel.P–01? (01––80)OK?––>SETFigure 1PAPER FEEDING DIRECTIONCutReg. Mark(Optional)Bar Code(Optional)ProgramNumberSlitCrease5There is creasing unit that performs creasesperpendicular to the line of the paper travel.Figure 253
Definition of Programming TermsPAPER FEEDING DIRECTIONReg. Mark(Optional)Bar Code(Optional)Left Margin Slitter(LEFT SL)Right Margin Slitter(RGHT SL)Center Left Slitter(C.L.SL)Center Right Slitter(C.R.SL)Center Slitter(OP 1)PAPER FEEDING DIRECTIONFirst CutReg. Mark(Optional)Bar Code(Optional)Crease(SCR 1)Last cutTip• Paper area before first cut and after last cut are considered to be scrap and will be choppedup for disposal in waste tray when AUTO CUT is selected. See the appendix (P.66) for informationabout automatic cutting.54
Page 6 and 7: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 8 and 9: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 10 and 11: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 12 and 13: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 14: Operating Instraction - DC545 HCPar
Page 17 and 18: Part Names and Their Functions○
Page 19 and 20: Chapter 2Before Using This Machine
Page 21 and 22: How to set up the System○ ○ ○
Page 23: Part Names and Their Functionsi!0oN
Page 26 and 27: Before Using This Machine - DC545 H
Page 28 and 29: Operating Instructions - DC545 HCEX
Page 30 and 31: Operating Instructions - DC545 HCEX
Page 32 and 33: Troubleshooting - DC545 HCEXTrouble
Page 34 and 35: Troubleshooting - DC545 HCEXError M
Page 40 and 41: Troubleshooting - DC545 HCEXWhen a
Page 56 and 57: Manual Programming - DC545 HCEXDefi
Page 58 and 59: Manual Programming - DC545 HCEXDefi
Page 60: Manual Programming - DC545 HCEXDefi
Page 63 and 64: Factory Preset JobsPROGRAMNUMBER #9
Page 65 and 66: Factory Preset JobsEuropePROGRAMNUM
Page 67 and 68: How to Manually Program a Job○
Page 73 and 74: Appendix - DC545 HC/DC545 HCEXThis
Page 75 and 76: SpecificationsSpecifications of Reg
Page 77 and 78: SpecificationsThe second program en
Page 79 and 80: SpecificationsSelect OptionsDelete
Page 81 and 82: SpecificationsPOSITIONING THE BAR C
Page 83 and 84: Specifications2. Non-Printing AreaR
Page 85 and 86: SpecificationsHow to do AUTO CUTWha
Page 87 and 88: MEMO
Page 89 and 90: MEMO

Docu Cutter DC-545 HC/DC-545 HCEX

Create successful ePaper yourself

Delete template?

Save as template?