Docu Cutter DC-545 HC/DC-545 HCEX

More documents

Recommendations

Info

Troubleshooting - DC545 HCEXError Messages––– E 2 –––RS232C ERRORCause• CCD is defective• Main PWB unit is defectiveProblem detected1. There was an abnormal transmission between the CCD and the DC-545.––– E 3 –––BARCODE ERRORCause• Bar code being used does not meet specifications• CCD is defective• Main PWB unit is defectiveProblem detected1. The bar code could not be read even after the paper fed the specified length (50 mm) after the bar code readingoperation started.124––– E 4 –––REG.MARK ERRORCause• Reg. mark being used does not meet specifications• CCD is defective• Main PWB unit is defectiveProblem detected1. The reg. mark could not be read even after the paper fed the specified length (40 mm) after the reg. mark readingoperation started.2. Mark 1 was less than 4.5 mm.635
Error Messages––– E 5 –––SLITTER ERROR *Slitter errors are numbered from 1 to 6.Cause• Slitter sensor is defective• Slitter positioning motor is defective• Main PWB unit is defectiveProblem detected1. Light did not transmit to the slitter sensor when temporarily shifting inward 8 mm to detect the home positionwhile the slitter sensor was shielded from light and the command to move the slitter was issued.2. The slitter did not return to the predetermined position within the specified time period (refer to the table below)after the command to move the slitter was issued.Left margin slitterRight margin slitterLeft center slitterRight center slitterOP1 slitterOP2 slitterTime until detection4.5 S5.5 S6.0 S6.0 S12.0S 6.0S(OP2: When not installed) (OP2: When installed)6.0S (Only when OP2 is installed.)AngleConnectorSensorThis image shows the optional 1 slitter sensor.You can identify the position of the slitter where the error that occurs by looking at the number in the message displayedon the LCD panel.LCD messageSLITTER ERROR 1SLITTER ERROR 2SLITTER ERROR 3SLITTER ERROR 4SLITTER ERROR 5SLITTER ERROR 6SlitterLeft margin slitterRight margin slitterLeft center slitterRight center slitterOP1 slitterOP2 slitter36
Page 6 and 7: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 8 and 9: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 10 and 11: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 12 and 13: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 14: Operating Instraction - DC545 HCPar
Page 17 and 18: Part Names and Their Functions○
Page 19 and 20: Chapter 2Before Using This Machine
Page 21 and 22: How to set up the System○ ○ ○
Page 23: Part Names and Their Functionsi!0oN
Page 26 and 27: Before Using This Machine - DC545 H
Page 28 and 29: Operating Instructions - DC545 HCEX
Page 30 and 31: Operating Instructions - DC545 HCEX
Page 32 and 33: Troubleshooting - DC545 HCEXTrouble
Page 34 and 35: Troubleshooting - DC545 HCEXError M
Page 38 and 39: Troubleshooting - DC545 HCEXError M
Page 40 and 41: Troubleshooting - DC545 HCEXWhen a
Page 54 and 55: Manual Programming - DC545 HCEXChap
Page 56 and 57: Manual Programming - DC545 HCEXDefi
Page 58 and 59: Manual Programming - DC545 HCEXDefi
Page 60: Manual Programming - DC545 HCEXDefi
Page 63 and 64: Factory Preset JobsPROGRAMNUMBER #9
Page 65 and 66: Factory Preset JobsEuropePROGRAMNUM
Page 67 and 68: How to Manually Program a Job○
Page 73 and 74: Appendix - DC545 HC/DC545 HCEXThis
Page 75 and 76: SpecificationsSpecifications of Reg
Page 77 and 78: SpecificationsThe second program en
Page 79 and 80: SpecificationsSelect OptionsDelete
Page 81 and 82: SpecificationsPOSITIONING THE BAR C
Page 83 and 84: Specifications2. Non-Printing AreaR
Page 85 and 86: SpecificationsHow to do AUTO CUTWha
Page 87 and 88:
MEMO
Page 89 and 90:
MEMO
show all

Docu Cutter DC-545 HC/DC-545 HCEX

Create successful ePaper yourself

Delete template?

Save as template?