Docu Cutter DC-545 HC/DC-545 HCEX

More documents

Recommendations

Info

Appendix - DC545 HC/DC545 HCEXSpecificationsTHE 'REG' (REGISTER) MARKUsing a CCD sensor to read an image reference point on the sheet is a unique feature of the DC-545.The mark is similar to a cutting mark (or crop mark) for guillotines. The device does not cut on this mark, it is simplya definable shape which is easy to recognize and is easy to reproduce in the original application.The reg. mark is actually made up of two components. The vertical component is used for determining the horizontalreference point. In other words, where the image is located from left to right on the sheet. When a job is programmedinto memory the first entry is MARK 1. This refers to the vertical line in the reg. mark. During the programmingprocess the MARK 1 value is entered in pulse counts. There are two ways to obtain the proper data value for MARK 1.Obtaining the MARK 1 value can be done with the two following methods.Obtaining MARK 1 Value - Method 1With this method, you can input the MARK 1 value through DC-545. Load the type of paper that is registered to for thefeed tray when inputting the MARK 1 value, and then press the key. The paper stops when it is in the vicinitywhere the MARK 1 value is read, move the paper forward and backward with the and keys to move the paperto the position where the MARK 1 value can be read. Then enter the value that is displayed on the screen.12Obtaining MARK 1 Value - Method 2You can enter the MARK 1 value with the following method, rather than method 1, if you know the MARK 1 position.Convert the MARK 1 value to a numerical value according to the following table and enter the new value, note that theMARK 1 value is not the distance (mm) from the edge of the paper.For example, if the MARK 1 is positioned 10 mm from the edge of the paper, then the MARK 1 value is 70.MM CCD Reading1 15+/- 12 21+/- 13 27+/- 14 33+/- 15 40+/- 16 46+/- 17 52+/- 18 58+/- 19 64+/- 110 70+/- 111 77+/- 112 83+/- 113 89+/- 114 95+/- 115 101+/- 116 107+/- 117 113+/- 118 120+/- 119 126+/- 120 132+/- 1MARK 1 CONVERSION TABLE73
SpecificationsThe second program entry is MARK 2. This refers to the horizontal line of the reg. mark and is used as the imagevertical reference point. This mark determines where the image reference is located in respect to the head and foot of thepage.MARK 1MARK 2MARK 1 corrects for errors in thisdirectionMARK 2 corrects for errors in thisdirection74
Page 6 and 7:
○ ○ ○ ○ ○ ○ ○ ○ ○
Page 8 and 9:
○ ○ ○ ○ ○ ○ ○ ○ ○
Page 10 and 11:
○ ○ ○ ○ ○ ○ ○ ○ ○
Page 12 and 13:
○ ○ ○ ○ ○ ○ ○ ○ ○
Page 14:
Operating Instraction - DC545 HCPar
Page 17 and 18:
Part Names and Their Functions○
Page 19 and 20:
Chapter 2Before Using This Machine
Page 21 and 22:
How to set up the System○ ○ ○
Page 23:
Part Names and Their Functionsi!0oN
Page 26 and 27: Before Using This Machine - DC545 H
Page 28 and 29: Operating Instructions - DC545 HCEX
Page 30 and 31: Operating Instructions - DC545 HCEX
Page 32 and 33: Troubleshooting - DC545 HCEXTrouble
Page 34 and 35: Troubleshooting - DC545 HCEXError M
Page 40 and 41: Troubleshooting - DC545 HCEXWhen a
Page 54 and 55: Manual Programming - DC545 HCEXChap
Page 56 and 57: Manual Programming - DC545 HCEXDefi
Page 58 and 59: Manual Programming - DC545 HCEXDefi
Page 60: Manual Programming - DC545 HCEXDefi
Page 63 and 64: Factory Preset JobsPROGRAMNUMBER #9
Page 65 and 66: Factory Preset JobsEuropePROGRAMNUM
Page 67 and 68: How to Manually Program a Job○
Page 73 and 74: Appendix - DC545 HC/DC545 HCEXThis
Page 75: SpecificationsSpecifications of Reg
Page 79 and 80: SpecificationsSelect OptionsDelete
Page 81 and 82: SpecificationsPOSITIONING THE BAR C
Page 83 and 84: Specifications2. Non-Printing AreaR
Page 85 and 86: SpecificationsHow to do AUTO CUTWha
Page 87 and 88: MEMO
Page 89 and 90: MEMO
show all

Docu Cutter DC-545 HC/DC-545 HCEX

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?