Docu Cutter DC-545 HC/DC-545 HCEX

More documents

Recommendations

Info

Manual Programming - DC545 HCEXDefinition of Programming TermsJOB DESIGN ISSUES1) Orientation of small format (business) cardsAlthough the smallest format supported is 88.9 x 50.8 mm, the 88.9 mm side must be in the direction of feed, otherwisethe pieces will drop between the transport rollers. This is because the center slitters must be able to move across thepaper path.12) Arrangement of small format (business) cards on large sheets (A3+ or oversized ledger)Business cards requiring a bleed and gutter, require the use of two slitters between each card. Because more businesscards are fit onto A3 or ledger in this format compared to A4 or letter, the number of slitters required will be more thanthe maximum of 4 available.5Workaround solution - arrange 12 to view on A3 or ledger, place the register mark in two positions, 210 mm apart. Printon A3, cut in half using a guillotine (or use the 545). Then place both stacks in the 545 and process as if A4 or letter.The reg. mark will enable the device to adjust and compensate both for image drift and for any inaccuracy in theguillotine cut.57
Definition of Programming TermsPrint, cut in half, process as if A4 or letter size3) Cutting guttersThe slitters cannot be positioned closer together than 50 mm. To perform a gutter cut of a few mm, use slitters on twoadjacent shafts, not those on the same shaft. The waste between gutters will exit onto the delivery tray.4) Location of right margin trim for A4 paperUnlike the center slitters, both margin slitters share common axis lead screws. Due to the need to support the marginslitters lead screws in the mid-area of the machine, a support was positioned approximately in the middle of the device.This means that the right trimmer cannot trim below the dimension of 200 mm from the reference (datum or nonoperatorside) edge.In the worst case the image can drift up to 2 mm so the trim position should not be located less than 202 mm from thereference edge.58
Page 6 and 7:
○ ○ ○ ○ ○ ○ ○ ○ ○
Page 8 and 9: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 10 and 11: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 12 and 13: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 14: Operating Instraction - DC545 HCPar
Page 17 and 18: Part Names and Their Functions○
Page 19 and 20: Chapter 2Before Using This Machine
Page 21 and 22: How to set up the System○ ○ ○
Page 23: Part Names and Their Functionsi!0oN
Page 26 and 27: Before Using This Machine - DC545 H
Page 28 and 29: Operating Instructions - DC545 HCEX
Page 30 and 31: Operating Instructions - DC545 HCEX
Page 32 and 33: Troubleshooting - DC545 HCEXTrouble
Page 34 and 35: Troubleshooting - DC545 HCEXError M
Page 40 and 41: Troubleshooting - DC545 HCEXWhen a
Page 54 and 55: Manual Programming - DC545 HCEXChap
Page 56 and 57: Manual Programming - DC545 HCEXDefi
Page 60: Manual Programming - DC545 HCEXDefi
Page 63 and 64: Factory Preset JobsPROGRAMNUMBER #9
Page 65 and 66: Factory Preset JobsEuropePROGRAMNUM
Page 67 and 68: How to Manually Program a Job○
Page 73 and 74: Appendix - DC545 HC/DC545 HCEXThis
Page 75 and 76: SpecificationsSpecifications of Reg
Page 77 and 78: SpecificationsThe second program en
Page 79 and 80: SpecificationsSelect OptionsDelete
Page 81 and 82: SpecificationsPOSITIONING THE BAR C
Page 83 and 84: Specifications2. Non-Printing AreaR
Page 85 and 86: SpecificationsHow to do AUTO CUTWha
Page 87 and 88: MEMO
Page 89 and 90: MEMO
show all

Docu Cutter DC-545 HC/DC-545 HCEX

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?