Docu Cutter DC-545 HC/DC-545 HCEX

More documents

Recommendations

Info

Troubleshooting - DC545 HCEXError Messages––– J 3 –––CENTER JAMCause• Paper does not meet specifications• The length of the JOB data and the paper are different.Problem detected1. The leading edge of the paper was not detected at PPS3 even though the specified length (100 mm) had passedPPS2.2. Paper was not released from PPS3 even though the preset registered paper length + 30 mm had passed PPS3.––– J 4 –––SLITTER OR STACKCause• Paper does not meet specifications• The length of the job data and the paper are different.• The stacker is full and paper can not be ejected.124Problem detected1. The leading edge of the paper was not detected at PPS4 even though the specified length (500 mm) had passedPPS3.2. Paper was not released from PPS4 even though the preset registered paper length + 50 mm had passed PPS4.––– J 5 –––OVER CAPACITYCause• There is too much paper loaded on the AF-100 feed tray.• Paper level sensor is defective• Actuator malfunction• Main PWB unit is defective6Problem detected1. Elevator lower switch was pressed after paper feed was started at DC-545HC while the paper level sensor was on.33
Error Messages––– J 7 –––CUTTER LOCKCause• Paper does not meet specifications• Cutter motor is defective• Cutter position switch is defective• Main PWB unit is defectiveProblem detected1. There was no response from the cutter position switch even though the specified time (0.6 seconds) elapsed aftercutting started.––– J 8 –––CREASE LOCKCause• Paper does not meet specifications• Creaser motor is defective• Creaser sensor is defective• Main PWB unit is defectiveProblem detected1. There was no response from the creaser sensor even though the specified time (2.0 seconds) elapsed after scoringstarted.––– E 1 –––COVER OPENCause• Actuator (N4-L224*&N4-225*) installation is incorrect• Interlock is defective• Main PWB unit is defectiveProblem detected1. One of the covers was open while the machine was operating.2. One of the covers was open when the start button was pushed.34
Page 6 and 7: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 8 and 9: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 10 and 11: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 12 and 13: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 14: Operating Instraction - DC545 HCPar
Page 17 and 18: Part Names and Their Functions○
Page 19 and 20: Chapter 2Before Using This Machine
Page 21 and 22: How to set up the System○ ○ ○
Page 23: Part Names and Their Functionsi!0oN
Page 26 and 27: Before Using This Machine - DC545 H
Page 28 and 29: Operating Instructions - DC545 HCEX
Page 30 and 31: Operating Instructions - DC545 HCEX
Page 32 and 33: Troubleshooting - DC545 HCEXTrouble
Page 36 and 37: Troubleshooting - DC545 HCEXError M
Page 38 and 39: Troubleshooting - DC545 HCEXError M
Page 40 and 41: Troubleshooting - DC545 HCEXWhen a
Page 54 and 55: Manual Programming - DC545 HCEXChap
Page 56 and 57: Manual Programming - DC545 HCEXDefi
Page 58 and 59: Manual Programming - DC545 HCEXDefi
Page 60: Manual Programming - DC545 HCEXDefi
Page 63 and 64: Factory Preset JobsPROGRAMNUMBER #9
Page 65 and 66: Factory Preset JobsEuropePROGRAMNUM
Page 67 and 68: How to Manually Program a Job○
Page 73 and 74: Appendix - DC545 HC/DC545 HCEXThis
Page 75 and 76: SpecificationsSpecifications of Reg
Page 77 and 78: SpecificationsThe second program en
Page 79 and 80: SpecificationsSelect OptionsDelete
Page 81 and 82: SpecificationsPOSITIONING THE BAR C
Page 83 and 84: Specifications2. Non-Printing AreaR
Page 85 and 86:
SpecificationsHow to do AUTO CUTWha
Page 87 and 88:
MEMO
Page 89 and 90:
MEMO
show all

Docu Cutter DC-545 HC/DC-545 HCEX

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?