MPH series video encoders - Teleste

More documents

Recommendations

Info

Tunneling ProtocolData port mode can be set to thetunneling protocol usage from theTerminal Server page.Tunnelling Protocol enables you to establish point to point connectionbetween encoder, decoder and management system. There are threeoptions, TCP server, TCP client and UDP multicast.Tunneling ConfigurationProtocol:Address:Port:StatusState:Client / server based connected is done by TCP client / server protocol. Ifthe encoder is set to be “TCP Server”, then the decoder or managementsystem must be set to “TCP Client”, or vice versa. In UDP multicastmode, you can use a joystick to control multiple cameras and connectioncan be point to multipoint.Destination IP addressUDP port number (0...65535). This number has to be same at both encoderand decoder pairs_________________________________________________________Shows data port’s state.Note! In order to have correct channel status information, you cancheck the followings:• Device address is configured correctly in PTZ nodes page.• Serial Port configuration : connection mode (RS-485 4-wire, etc),Baud rate, and parity. in terminal server page.• PTZ configuration is added to a media profile. PTZ configuration“PTZ1” by default is added to media Profile 1.Data counter: Data port’s traffic counter.26 MPH100/400 series video encoders WebUI user manual
ONVIF PTZ service1. In order to activate the ONVIF PTZprotocol, data port mode must be firstset to the ONVIF PTZ service usagefrom the Terminal Server page.ONVIF PTZ service lets you control the camera from ONVIF clientapplication. ONVIF PTZ service is available from data channel 1. Itmeans that MPH converts ONVIF PTZ commands to Pelco Dcommands and transmits that to the camera via Data channel 1.2. Next on the PTZ Nodes page you need to set a Bus address for thecamera, you can have two cameras using the same Data port with differentbus addresses.3. Then on the PTZ configurations page you can set limitations for PTZoperations. For each PTZ node you can limit speed, pan, tilt and zoom.1TERMINAL SERVICE(enable ONVIF PTZ on DATA 1)2PTZ NODE(set a bus address for camera)3PTZ CONFIGURATIONS(set limitations for PTZ operations)4MEDIA PROFILE(PTZ configurations assignment)Step-by-step flowchart how toconfigure ONVIF PTZ data 1 channelin the MPH encoder.4. Finally on the Media profiles page you need to assign the PTZconfiguration to the media profile where the camera is connected to.MPH100/400 series video encoders WebUI user manual 27
Page 1 and 2: User Manual - MPH100/400MPH series
Page 4 and 5: MPH Series Video Encoders Front and
Page 6 and 7: Getting startedQuick instructions11
Page 8 and 9: Ethernet InterfaceEthernet connecti
Page 10 and 11: Management Interface9 10 11 12 13 1
Page 12 and 13: Starting WebUI sessionTo create a W
Page 14 and 15: Configuring Video ChannelsVideo con
Page 16 and 17: 1. Video InterfacesClick “Video I
Page 18 and 19: 3. Video EncodersClick “Video Enc
Page 20 and 21: Advanced simple profile:H.264 optio
Page 22: Video streaming performanceThe foll
Page 25 and 26: Configuring Data Channels9 10 11 12
Page 27: CommonName:Mode:Baud rate:Data bits
Page 31 and 32: CommonName:Input filter:Filtering t
Page 33 and 34: Video Analytics configuration isact
Page 35 and 36: CommonType:Module:Link status:Ether
Page 37 and 38: Local TimeTime zone:Local time:Syst
Page 39 and 40: The Real Time Streaming Protocol(RT
Page 41 and 42: Command Line Interface - CLIGeneral
Page 43 and 44: Connection methods - TCP/IPThis cha
Page 45 and 46: Devmgmt commandEnter the devmgmt co
Page 47 and 48: Network commandEnter the network co
Page 49 and 50: MPH featuresVideo MPH101/111 MPH102
Page 51 and 52: NotesMPH100/400 series video encode

MPH series video encoders - Teleste

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?