MPH series video encoders - Teleste

More documents

Recommendations

Info

Ethernet InterfaceEthernet connectionsElectrical Ethernet connector (RJ-45).MPH encoder supports both Fast Ethernet and Gigabit Ethernet connectionspeeds. Ethernet interface type is either a fixed electrical (copper), orhas support for a small form-factor pluggable transceiver (SFP) module.Supported SFP transceivers are specified by Teleste. Please see the latestlits of available products.Led Colour Mode21GreenBlinking GreenOFF / DarkOrangeOFF / DarkLink upTrafficNo link1000 Mbps100 MbpsEthernet port’s led indicator operation(RJ-45 connector).Led Colour ModeSFPGreenBlinking GreenOFF / DarkLink upTrafficNo linkEthernet port’s led indicator operation(when SFP optical connector).Fixed electrical interfaceThe electrical Ethernet connector type is a RJ-45 female. The connector isfixed (except Gigabit model with GTA/GTR type of SFP). Depending onthe model, the Ethernet interface speed is 10/100BASE-T (Fast Ethernet)or 10/100/1000BASE-T (Gigabit Ethernet).Power over Ethernet (PoE) optionMPH100 series encoders supports PoE standard (802.3af). This meansthat the encoders can be powered through the LAN cable (CAT5) withoutthe need of individual power supplies.Requirements for the use of PoE:• A Power over Ethernet (PoE) compliant switch or hub.• MLH251 license activation.INVISIBLE LASERRADIATIONCLASS 1Note! 100BASE-FX SFP module isalways supported, 1000BASE-X SFPmodule has to be activated with therequired license (MLH241).Optical interfaceThe optical Ethernet interface is type of a small form-factor pluggable(SFP). SFP modules for optical Ethernet operation are available with avariety of different types, allowing users to select the suitable module forto provide the required optical reach over the available optical fibre type.The optical connector type is LC (single or dual). Depending on themodel, the Ethernet interface speed is 100BASE-F (Fast Ethernet) or1000BASE-X (Gigabit Ethernet). The optical output level is constant andcannot be adjusted.When installing the fibre optic cable, do not exceed the minimumbending radius when connecting cable to the system.Optical Ethernet connection meets class 1 laser safety requirements ofIEC 60825-2: 2004 and US department of health services 21 CFR1040.10 and 1040.11 (1990) when operated within the specified temperature,power supply and duty cycle ranges.6 MPH100/400 series video encoders WebUI user manual
How to unplug or plug-in the SFP transceiver moduleIf your up-link port requirements change, simply unplug the existing SFPmodule, and plug-in the new module. The SFP transceiver modulesmust be installed before the encoder is powered on.2 fibre version 1 fibre versionTx Rx Tx/RxSFP plug-in optical transceiver module.The SFP transceiver module has a bale-clasp latch that makes easier toinstall or remove the module. Protect the SFP module by inserting aclean dustplug into the module after you remove the fiber cable. Be sureto clean the optic surfaces of the fiber cable before you plug the cableinto another module. When using 2 fibre version SFP, select carefullythe correct optical port for TX and RX operation.To unplug and plug-in the SFP module, follow these steps1. Open the bale clasp on the SFP module by pressing the claspdownward until it is in a horizontal position.2. Use a small flat-blade screwdriver or other long, narrow instrument topush on the hinge pin to unlock the SFP cage latch.Optical connector is the type of LC.3. Grasp the SFP module by the bale clasp and gently pull it out of theSFP cage.To plug-in the module:1. Orient the transceiver with the bale clasp on the bottom, close thebale clasp by pushing it up over the transceiver, then gently insertthe transceiver into the port until it clicks into place.bale claspNote! Reboot the device when the SFP is changed.Some generic notes for successfull optical connections:latchSFP module’s locking release points.• Ensure that the fiber patch cord is damage-free (fiber condition canbe easily checked by a visible laser tester)• Do not exceed the minimum bending radius of the fibre• Avoid sharp corners on cable shelves and in cable managementin overall• Make sure that correct optical connectors are used• Open connectors are always secured by dustcaps during maintenance• Always before mating clean all connectors (wet cleaning by highpurity alcohol & drying, or dry cleaning with reel-based lint-free wipes,fiber adapters may require special ferrule end-face cleaning tools)• Before making any visual inspections ensure that system has beenshutdown or no optical power is present• For fault finding at least a optical power meter is required, a complexfiber cable environment may require use of an OTDR equipmentMPH100/400 series video encoders WebUI user manual 7
Page 1 and 2: User Manual - MPH100/400MPH series
Page 4 and 5: MPH Series Video Encoders Front and
Page 6 and 7: Getting startedQuick instructions11
Page 10 and 11: Management Interface9 10 11 12 13 1
Page 12 and 13: Starting WebUI sessionTo create a W
Page 14 and 15: Configuring Video ChannelsVideo con
Page 16 and 17: 1. Video InterfacesClick “Video I
Page 18 and 19: 3. Video EncodersClick “Video Enc
Page 20 and 21: Advanced simple profile:H.264 optio
Page 22: Video streaming performanceThe foll
Page 25 and 26: Configuring Data Channels9 10 11 12
Page 27 and 28: CommonName:Mode:Baud rate:Data bits
Page 29 and 30: ONVIF PTZ service1. In order to act
Page 31 and 32: CommonName:Input filter:Filtering t
Page 33 and 34: Video Analytics configuration isact
Page 35 and 36: CommonType:Module:Link status:Ether
Page 37 and 38: Local TimeTime zone:Local time:Syst
Page 39 and 40: The Real Time Streaming Protocol(RT
Page 41 and 42: Command Line Interface - CLIGeneral
Page 43 and 44: Connection methods - TCP/IPThis cha
Page 45 and 46: Devmgmt commandEnter the devmgmt co
Page 47 and 48: Network commandEnter the network co
Page 49 and 50: MPH featuresVideo MPH101/111 MPH102
Page 51 and 52: NotesMPH100/400 series video encode

MPH series video encoders - Teleste

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?