BROOKFIELD DV-II+ PROGRAMMABLE VISCOMETER Operating ...

More documents

Recommendations

Info

L°F(FAHRENHEIT)CGS UNITSL°C(CENTIGRADE)CGS UNITSL°F(FAHRENHEIT)CGS UNITSL°F(FAHRENHEIT)SI UNITSLCGS UNITSSEQUENTIALLCGS UNITSINTERLEAVELCGS UNITSCUSTOM SPEEDSLSEQUENTIALPRINT SERIALLSEQUENTIALPRINT PARALLELLPRINT SERIALDATA AVERAGINGOPTIONSTABFigure 25III.2.1 Temperature DisplayThe DV-II+ viscometer can display temperature in either degrees Centigrade or degrees Fahrenheit.On entry (assuming the viscometer is currently displaying °F) you will be presented with:L°F(FAHRENHEIT)CGS UNITSFigure 26A press of the OPTIONS/TAB key at this point will “toggle” between the two available temperaturescale options as shown in Figure 27:L°F(FAHRENHEIT)CGS UNITSL°C(CENTIGRADE)CGS UNITSFigure 27To select the temperature display mode, press the ENTER/AUTORANGE key. You automatically exitthe Setup menu with the viscometer displaying temperature in the selected scale. You must press theENTER/AUTORANGE key to select the flashing option.III.2.2 Units of MeasurementSelecting units of measurement is identical to that for temperature described above. The screendisplay shows:Brookfield Engineering Labs., Inc. Page 22 Manual No. M/97-164-F1102
L°F(FAHRENHEIT)CGS UNITSFigure 28A press of the OPTIONS/TAB key at this point allows the user to “toggle” between the two availabledata display units as shown in Figure 29:L°F(FAHRENHEIT)CGS UNITSL°F(FAHRENHEIT)SI UNITSFigure 29Pressing the ENTER/AUTORANGE key selects the display units, which are flashing, followed by anexit of the Setup menu. You must press the ENTER/AUTORANGE key to select the flashing option.III.2.3 Motor Speed Set SelectionThis selection must be done with the motor off. Scrolling in the Setup options menu to the speed setselection option yields the following screen display:LCGS UNITSSEQUENTIALFigure 30The last selected speed set option is displayed, in this case, Sequential. For each press of theOPTIONS/TAB key, the display shows selectable options (Figure 31). You must press the ENTER/AUTORANGE key to select the flashing option.LCGS UNITSINTERLEAVELCGS UNITSCUSTOM SPEEDSLCGS UNITSSEQUENTIALFigure 31The speeds available in each of the above options are listed in Appendix F. The DV-II+ is initiallyset up with the Sequential Speed Set at Brookfield prior to shipment.III.2.3.1 LV/RV SpeedsIn the case of Sequential or Interleave, a press of the ENTER/AUTORANGE key immediately selectsthat option and exits the SETUP option menu.Brookfield Engineering Labs., Inc. Page 23 Manual No. M/97-164-F1 102
Page 1 and 2: BROOKFIELD DV-II+PROGRAMMABLE VISCO
Page 4 and 5: I.1 ComponentsComponent Part Number
Page 6 and 7: I.4 InstallationNote: “IQ, OQ, PQ
Page 8 and 9: SELECTDISPLAYSELECT DISPLAYSelects
Page 10 and 11: II.GETTING STARTEDII.1AutozeroBefor
Page 12 and 13: II.3SETSPEED Speed Selection, Setti
Page 14 and 15: SR 40.0 20.1C6.0RPM % 15.6Figure 13
Page 16 and 17: II.7 Temperature DisplayThe DV-II+
Page 18 and 19: Non-Newtonian fluid behavior can re
Page 20 and 21: OPTIONSTABOPTIONS/TAB - Toggles bet
Page 24 and 25: III.2.3.2 Custom SpeedsPressing the
Page 26 and 27: III.3.1 Time to StopOn entry, the u
Page 28 and 29: standard print string to the attach
Page 30 and 31: However, upon starting the timed op
Page 32 and 33: Refer to Section IV for information
Page 34 and 35: CP 123.4 55.1C10 RPM PGM% 63.7Figur
Page 36 and 37: IV.2 Description of B.E.V.I.S. Comm
Page 38 and 39: Figure 67 shows the grid where the
Page 40 and 41: IV. 5 Example ProgramsThe following
Page 42 and 43: Appendix A - Cone/Plate Viscometer
Page 44 and 45: A.3 SETTING THE GAP1. Move the togg
Page 46 and 47: Appendix B - Viscosity RangesViscos
Page 48 and 49: The second consideration involves t
Page 50 and 51: container wall and the spindle surf
Page 52 and 53: Table D1 (continued)SC4-14 14 125 0
Page 54 and 55: Appendix E - Calibration Procedures
Page 56 and 57: 4) Allow 30 minutes for the viscosi
Page 58 and 59: Interpretation of Calibration Test
Page 60 and 61: many viscometer users the true visc
Page 62 and 63: Appendix G - CommunicationsWhen usi
Page 64 and 65: DV-II+Serial and Analog OutputsNo C
Page 66 and 67: UnpackingCheck carefully to see tha
Page 68 and 69: Appendix J - Fault Diagnosis and Tr
Page 70 and 71: ❏ No Recorder Response✓ Be Sure
Page 72 and 73:
Appendix K - Warranty Repair and Se
Page 74 and 75:
Providing us with the following inf
show all

BROOKFIELD DV-II+ PROGRAMMABLE VISCOMETER Operating ...

Create successful ePaper yourself

Delete template?

Save as template?