BROOKFIELD DV-II+ PROGRAMMABLE VISCOMETER Operating ...

More documents

Recommendations

Info

Table D1 (continued)SC4-14 14 125 0.4SC4-15 15 50 0.48SC4-16 16 128 0.2929SC4-18 18 3.2 1.32SC4-21 21 5 0.93SC4-25 25 512 0.22SC4-27 27 25 0.34SC4-28 28 50 0.28SC4-29 29 100 0.25SC4-31 31 32 0.34SC4-34 34 64 0.28SC4-37 37 25 0.36CPE-40 40 0.327 7.5CPE-41 41 1.228 2CPE-42 42 0.64 3.8CPE-51 51 5.12 3.84CPE-52 52 9.83 2V-71 71 2.62 NAV-72 72 11.10 NAV-73 73 53.50 NATable D2 lists the model codes and spring torque constants for each Viscometer model.Table D2MODELTKMODEL CODEON DV-II+ SCREENLVDV-II+ 0.09373 LV2.5LVDV-II+ 0.2343 2.5 LV5LVDV-II+ 0.4686 5 LV1/4 RVDV-II+ 0.25 1/4 RV1/2 RVDV-II+ 0.5 1/2 RVRVDV-II+ 1 RVHADV-II+ 2 HA2HADV-II+ 4 2 HA2.5HADV-II+ 5 2.5 HAHBDV-II+ 8 HB2HBDV-II+ 16 2 HB2.5HBDV-II+ 20 2.5 HB5HBDV-II+ 40 5 HBBrookfield Engineering Labs., Inc. Page 52 Manual No. M/97-164-F1102
The full scale viscosity range for any DV-II+ model and spindle may be calculated using theequation:10,000Full Scale Viscosity Range [cP] = TK * SMC * RPMwhere:TK = DV-II+ Torque Constant from Table D2SMC = Spindle Multiplier Constant from Table D1The Shear Rate calculation is:Shear Rate ( 1 / Sec ) = SRC * RPMwhere:SRC = Shear Rate Constant from Table D1Brookfield Engineering Labs., Inc. Page 53 Manual No. M/97-164-F1 102
Page 1 and 2: BROOKFIELD DV-II+PROGRAMMABLE VISCO
Page 4 and 5: I.1 ComponentsComponent Part Number
Page 6 and 7: I.4 InstallationNote: “IQ, OQ, PQ
Page 8 and 9: SELECTDISPLAYSELECT DISPLAYSelects
Page 10 and 11: II.GETTING STARTEDII.1AutozeroBefor
Page 12 and 13: II.3SETSPEED Speed Selection, Setti
Page 14 and 15: SR 40.0 20.1C6.0RPM % 15.6Figure 13
Page 16 and 17: II.7 Temperature DisplayThe DV-II+
Page 18 and 19: Non-Newtonian fluid behavior can re
Page 20 and 21: OPTIONSTABOPTIONS/TAB - Toggles bet
Page 22 and 23: L°F(FAHRENHEIT)CGS UNITSL°C(CENTI
Page 24 and 25: III.2.3.2 Custom SpeedsPressing the
Page 26 and 27: III.3.1 Time to StopOn entry, the u
Page 28 and 29: standard print string to the attach
Page 30 and 31: However, upon starting the timed op
Page 32 and 33: Refer to Section IV for information
Page 34 and 35: CP 123.4 55.1C10 RPM PGM% 63.7Figur
Page 36 and 37: IV.2 Description of B.E.V.I.S. Comm
Page 38 and 39: Figure 67 shows the grid where the
Page 40 and 41: IV. 5 Example ProgramsThe following
Page 42 and 43: Appendix A - Cone/Plate Viscometer
Page 44 and 45: A.3 SETTING THE GAP1. Move the togg
Page 46 and 47: Appendix B - Viscosity RangesViscos
Page 48 and 49: The second consideration involves t
Page 50 and 51: container wall and the spindle surf
Page 54 and 55: Appendix E - Calibration Procedures
Page 56 and 57: 4) Allow 30 minutes for the viscosi
Page 58 and 59: Interpretation of Calibration Test
Page 60 and 61: many viscometer users the true visc
Page 62 and 63: Appendix G - CommunicationsWhen usi
Page 64 and 65: DV-II+Serial and Analog OutputsNo C
Page 66 and 67: UnpackingCheck carefully to see tha
Page 68 and 69: Appendix J - Fault Diagnosis and Tr
Page 70 and 71: ❏ No Recorder Response✓ Be Sure
Page 72 and 73: Appendix K - Warranty Repair and Se
Page 74 and 75: Providing us with the following inf

BROOKFIELD DV-II+ PROGRAMMABLE VISCOMETER Operating ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?