BROOKFIELD DV-II+ PROGRAMMABLE VISCOMETER Operating ...

More documents

Recommendations

Info

DV-II+Serial and Analog OutputsNo ConnectionNo ConnectionTransmit Data (TxD)High Speed Print(Note 1)Serial Ground123456789Analog GroundAnalog % Torque(Note 2)Analog Temperature(Note 3)High Speed Print(Note 1)Notes:Figure G11. Placing a jumper across pins 4 and 9 causes the DV-II+ to output printerdata at a 3 line-per-second rate. No jumper across pins 4 and 9 retains theonce-per-second printer output rate.2. This is a 0-1 volt d.c. output where 0 volts corresponds to 0% torque and1 volt corresponds to 100 % torque with a resolution of 1 millivolt (0.1%).3. This is a 0-3.75 volt d.c. output where 0 volts corresponds to -100°C and3.75 volts corresponds to +275°C with a resolution of 1 millivolt (0.1°C).Analog Output:The analog outputs for temperature and % torque are accessed from the 9-pin connector located onthe rear panel of the DV-II+. The pin connections are shown in Figure G1.The output cable (Part No. DVP-96Y) connections are:Red Wire:Black Wire:White Wire:Green Wire:Temperature OutputTemperature Ground% Torque Output% Torque GroundNote:Please contact Brookfield Engineering Laboratories or your local dealer/distributor for purchase of the DVP-96Y analog output cable.Brookfield Engineering Labs., Inc. Page 64 Manual No. M/97-164-F1102
Appendix H - Model S Laboratory StandVS-35YMODEL SCLAMP ASSEMBLY761 811910BROOKFIELDLABORATORYVISCOMETERVS-17SYMODEL S-ECLAMP ASSEMBLY(EXPLOSION-PROOF)13151421612345ITEM PART #12345678910VS-34VS-38VS-2VS-350S311824S06B502020032S34ZVS-35VS-40YVS-41YVS-29VS-29W14” UPRIGHT ROD18” UPRIGHT RODDESCRIPTIONBASELEVELING SCREWSCREW, 5/16-18 X 3/4 LG. SLOTTED PAN HD.LOCKWASHER, EXTERNAL TOOTH, 5/16 X 5/8 X 1/32CLAMPGEAR SCREW ASSEMBLYCLAMP SCREW ASSEMBLYTENSION INSERTBELLEVILLE SPRING WASHERQTY.1OPTIONAL121111112EXPLOSION-PROOFCLAMP VS-17Y PARTS111213141516VS-2850S103208S25BVSXA-17Y50S252024E140VS-46YVS-45YTENSION SCREWSCREW, #10-32 X 1/4 LG. SLOTTED SETCLAMP ASSEMBLYSCREW, 1/4-20 X 3/4 LG. SOC. HD. CAP, 18-8 SSMODEL S-E GEAR SCREW ASSEMBLYMODEL S-E CLAMP SCREW ASSEMBLY111111Figure H1Brookfield Engineering Labs., Inc. Page 65 Manual No. M/97-164-F1 102
Page 1 and 2:
BROOKFIELD DV-II+PROGRAMMABLE VISCO
Page 4 and 5:
I.1 ComponentsComponent Part Number
Page 6 and 7:
I.4 InstallationNote: “IQ, OQ, PQ
Page 8 and 9:
SELECTDISPLAYSELECT DISPLAYSelects
Page 10 and 11:
II.GETTING STARTEDII.1AutozeroBefor
Page 12 and 13:
II.3SETSPEED Speed Selection, Setti
Page 14 and 15: SR 40.0 20.1C6.0RPM % 15.6Figure 13
Page 16 and 17: II.7 Temperature DisplayThe DV-II+
Page 18 and 19: Non-Newtonian fluid behavior can re
Page 20 and 21: OPTIONSTABOPTIONS/TAB - Toggles bet
Page 22 and 23: L°F(FAHRENHEIT)CGS UNITSL°C(CENTI
Page 24 and 25: III.2.3.2 Custom SpeedsPressing the
Page 26 and 27: III.3.1 Time to StopOn entry, the u
Page 28 and 29: standard print string to the attach
Page 30 and 31: However, upon starting the timed op
Page 32 and 33: Refer to Section IV for information
Page 34 and 35: CP 123.4 55.1C10 RPM PGM% 63.7Figur
Page 36 and 37: IV.2 Description of B.E.V.I.S. Comm
Page 38 and 39: Figure 67 shows the grid where the
Page 40 and 41: IV. 5 Example ProgramsThe following
Page 42 and 43: Appendix A - Cone/Plate Viscometer
Page 44 and 45: A.3 SETTING THE GAP1. Move the togg
Page 46 and 47: Appendix B - Viscosity RangesViscos
Page 48 and 49: The second consideration involves t
Page 50 and 51: container wall and the spindle surf
Page 52 and 53: Table D1 (continued)SC4-14 14 125 0
Page 54 and 55: Appendix E - Calibration Procedures
Page 56 and 57: 4) Allow 30 minutes for the viscosi
Page 58 and 59: Interpretation of Calibration Test
Page 60 and 61: many viscometer users the true visc
Page 62 and 63: Appendix G - CommunicationsWhen usi
Page 66 and 67: UnpackingCheck carefully to see tha
Page 68 and 69: Appendix J - Fault Diagnosis and Tr
Page 70 and 71: ❏ No Recorder Response✓ Be Sure
Page 72 and 73: Appendix K - Warranty Repair and Se
Page 74 and 75: Providing us with the following inf
show all

BROOKFIELD DV-II+ PROGRAMMABLE VISCOMETER Operating ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?