BROOKFIELD DV-II+ PROGRAMMABLE VISCOMETER Operating ...

More documents

Recommendations

Info

❏ No Recorder Response✓ Be Sure the viscometer is not at ZERO reading.✓ Be sure the recorder is ON and not on STANDBY.✓ Verify the range settings.✓ Check cable leads for clean connection.❏ Recorder Pen Moves in Wrong Direction✓ Output polarity reversed• Reverse leads❏ Viscometer Will Not Communicate with PC✓ Check the comm port and make sure the correct port is being utilized.✓ Check the interconnecting cable for proper installation✓ Check the Options menu and make sure the PC PROG is set to either “ON” or “OFF” inaccordance with the operating instructions for the program/procedure in use.If the above do not rectify the problem, do the following:✓ Shut off viscometer✓ Attach printer.✓ Press and hold the MOTOR ON/OFF and ENTER/AUTORANGE keys simulanteously whileturning the viscometer power on. Figure J1 appears on the viscometer display.<strong>VISCOMETER</strong> SETUPENTER TO STARTFigure J1✓ Press ENTER/AUTORANGE key and Figure J2 appears.PRINT PARAM RAM?NO THEN ENTERPRINT PARAM RAM?YES THEN ENTERFigure J2✓ Scroll to YES and press the ENTER/AUTORANGE key. Figure J3 appears.READY PRINTERENTER TO STARTFigure J3Brookfield Engineering Labs., Inc. Page 70 Manual No. M/97-164-F1102
✓ Press ENTER/AUTORANGE. Information similar to Figure J4 will appear on your printeroutput.Timed Stop Minutes 01Seconds 30RPM 50Time to Torque Torque % 60RPM 50Print Interval Minutes 00Seconds 05Printer Port Parallel or Serial ParallelLast Spindle Used 05Special Spindle AA SMC 0000.000Special Spindle AA SRC 00.000Special Spindle BB SMC 0000.000Special Spindle BB SRC 00.000Special Spindle CC SMC 0000.000Special Spindle CC SRC 00.000Special Spindle DD SMC 0000.000Special Spindle DD SRC 00.000Display UnitsCGSTemperature ScaleCSpeed SetINTERLEAVEViscometer ModelRVLast BEVIS Program 1Raw Temps2E0C 00FETorque ScaleE19FFigure J4✓ Call Brookfield to review the information on your printer output.✓ Figure J5 next appears on the viscometer display. Turn the viscometer power off.SETUP COMPLETETURN POWER OFFFigure J5Brookfield Engineering Labs., Inc. Page 71 Manual No. M/97-164-F1 102
Page 1 and 2:
BROOKFIELD DV-II+PROGRAMMABLE VISCO
Page 4 and 5:
I.1 ComponentsComponent Part Number
Page 6 and 7:
I.4 InstallationNote: “IQ, OQ, PQ
Page 8 and 9:
SELECTDISPLAYSELECT DISPLAYSelects
Page 10 and 11:
II.GETTING STARTEDII.1AutozeroBefor
Page 12 and 13:
II.3SETSPEED Speed Selection, Setti
Page 14 and 15:
SR 40.0 20.1C6.0RPM % 15.6Figure 13
Page 16 and 17:
II.7 Temperature DisplayThe DV-II+
Page 18 and 19:
Non-Newtonian fluid behavior can re
Page 20 and 21: OPTIONSTABOPTIONS/TAB - Toggles bet
Page 22 and 23: L°F(FAHRENHEIT)CGS UNITSL°C(CENTI
Page 24 and 25: III.2.3.2 Custom SpeedsPressing the
Page 26 and 27: III.3.1 Time to StopOn entry, the u
Page 28 and 29: standard print string to the attach
Page 30 and 31: However, upon starting the timed op
Page 32 and 33: Refer to Section IV for information
Page 34 and 35: CP 123.4 55.1C10 RPM PGM% 63.7Figur
Page 36 and 37: IV.2 Description of B.E.V.I.S. Comm
Page 38 and 39: Figure 67 shows the grid where the
Page 40 and 41: IV. 5 Example ProgramsThe following
Page 42 and 43: Appendix A - Cone/Plate Viscometer
Page 44 and 45: A.3 SETTING THE GAP1. Move the togg
Page 46 and 47: Appendix B - Viscosity RangesViscos
Page 48 and 49: The second consideration involves t
Page 50 and 51: container wall and the spindle surf
Page 52 and 53: Table D1 (continued)SC4-14 14 125 0
Page 54 and 55: Appendix E - Calibration Procedures
Page 56 and 57: 4) Allow 30 minutes for the viscosi
Page 58 and 59: Interpretation of Calibration Test
Page 60 and 61: many viscometer users the true visc
Page 62 and 63: Appendix G - CommunicationsWhen usi
Page 64 and 65: DV-II+Serial and Analog OutputsNo C
Page 66 and 67: UnpackingCheck carefully to see tha
Page 68 and 69: Appendix J - Fault Diagnosis and Tr
Page 72 and 73: Appendix K - Warranty Repair and Se
Page 74 and 75: Providing us with the following inf
show all

BROOKFIELD DV-II+ PROGRAMMABLE VISCOMETER Operating ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?