BROOKFIELD DV-II+ PROGRAMMABLE VISCOMETER Operating ...

More documents

Recommendations

Info

many viscometer users the true viscosity is not as important as a repeatable day to day value. Thisrepeatable value can be obtained without any special effort for any measurement circumstance. But, itshould be known that this type of torque reading will not convert into a correct centipoise value whenusing a Brookfield factor if the boundary conditions are not those specified by Brookfield.The guard leg is a part of the calibration check of the Brookfield LV and RV series Viscometer/Rheometer. Our customers should be aware of its existence, its purpose and the effect that it may haveon data. With this knowledge, the viscometer user may make modifications to the recommended methodof operation to suit their needs.Brookfield Engineering Labs., Inc. Page 60 Manual No. M/97-164-F1102
Appendix F - Speed SetsThe following speed sets and custom speeds are selectable from the SETUP menu option. Allspeeds are in units of RPM.InterleaveSpeed From0.00.30.50.61.01.52.02.53.04.05.06.010.012.020.030.050.060.0100.0LVTRVTLVTRVTLVTRVFRVTLVTRVFRVTLVTRVTLVTRVTLVTRVTLVTRVTORSequentialSpeed From0.00.30.61.53.06.012.030.060.00.00.51.02.02.54.05.010.020.050.0100.0LVTLVTLVTLVTLVTLVTLVTLVTRVTRVTRVFRVTRVFRVTRVTRVTRVTRVTORSpeed0.00.010.030.050.070.090.10.20.30.40.50.60.70.80.91.01.11.21.41.51.82.02.5CustomSpeed3.04.05.06.07.58.010.012.015.017.020.022.025.030.035.040.045.050.060.070.075.080.090.0Speed100.0105.0120.0135.0140.0150.0160.0180.0200.0The DV-II+ has thesequential speed setinstalled atBrookfield prior toshipment.The DV-II+ can be programmed toselect up to 18 of the above speedsfor use at any one time. Speed 0.0 isautomatically included as the 19thspeed.Brookfield Engineering Labs., Inc. Page 61 Manual No. M/97-164-F1 102
Page 1 and 2:
BROOKFIELD DV-II+PROGRAMMABLE VISCO
Page 4 and 5:
I.1 ComponentsComponent Part Number
Page 6 and 7:
I.4 InstallationNote: “IQ, OQ, PQ
Page 8 and 9:
SELECTDISPLAYSELECT DISPLAYSelects
Page 10 and 11: II.GETTING STARTEDII.1AutozeroBefor
Page 12 and 13: II.3SETSPEED Speed Selection, Setti
Page 14 and 15: SR 40.0 20.1C6.0RPM % 15.6Figure 13
Page 16 and 17: II.7 Temperature DisplayThe DV-II+
Page 18 and 19: Non-Newtonian fluid behavior can re
Page 20 and 21: OPTIONSTABOPTIONS/TAB - Toggles bet
Page 22 and 23: L°F(FAHRENHEIT)CGS UNITSL°C(CENTI
Page 24 and 25: III.2.3.2 Custom SpeedsPressing the
Page 26 and 27: III.3.1 Time to StopOn entry, the u
Page 28 and 29: standard print string to the attach
Page 30 and 31: However, upon starting the timed op
Page 32 and 33: Refer to Section IV for information
Page 34 and 35: CP 123.4 55.1C10 RPM PGM% 63.7Figur
Page 36 and 37: IV.2 Description of B.E.V.I.S. Comm
Page 38 and 39: Figure 67 shows the grid where the
Page 40 and 41: IV. 5 Example ProgramsThe following
Page 42 and 43: Appendix A - Cone/Plate Viscometer
Page 44 and 45: A.3 SETTING THE GAP1. Move the togg
Page 46 and 47: Appendix B - Viscosity RangesViscos
Page 48 and 49: The second consideration involves t
Page 50 and 51: container wall and the spindle surf
Page 52 and 53: Table D1 (continued)SC4-14 14 125 0
Page 54 and 55: Appendix E - Calibration Procedures
Page 56 and 57: 4) Allow 30 minutes for the viscosi
Page 58 and 59: Interpretation of Calibration Test
Page 62 and 63: Appendix G - CommunicationsWhen usi
Page 64 and 65: DV-II+Serial and Analog OutputsNo C
Page 66 and 67: UnpackingCheck carefully to see tha
Page 68 and 69: Appendix J - Fault Diagnosis and Tr
Page 70 and 71: ❏ No Recorder Response✓ Be Sure
Page 72 and 73: Appendix K - Warranty Repair and Se
Page 74 and 75: Providing us with the following inf
show all

BROOKFIELD DV-II+ PROGRAMMABLE VISCOMETER Operating ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?