P1DMountingsCombinationsType and descriptionCylinders complete with mountings, sensors, speed regulation, fittings etc.Order a complete working unit on a single order code instead of a lot of separate numbers.Save time in all phases, such as purchasing, goods reception and installation.A factory installed complete cylinder makes your work more efficient!Configure functions and equipment in the order key. See pages 28-49 and 78-82.3 and 4 position <strong>cylinders</strong>This type of cylinder function consists of two <strong>cylinders</strong> installed back to back. Two<strong>cylinders</strong> with the same stroke give a 3 position cylinder with a symmetrical centre position,whereas different strokes give a 4 position cylinder where the two central positions can becalculated from the different stroke lengths.3 and 4 position <strong>cylinders</strong> can be ordered in two ways.Factory-fitted P1D-TTie-rod P1D <strong>cylinders</strong> are completed at the factory and are joined together as one unit byspecial tie-rods, see position 9 in the order key. See pages 36 and 80-82.Installation kit for all designsThere is an installation kit for cylinder bores 32 – 100 mm which makes it possible to joinany two P1D <strong>cylinders</strong> together at any time, to make a 3 or 4 position cylinder.Please refer to cylinder mountings, page 59.Cylinder A, P1D-T A, P1D-Sbore. mm mm mm32 247 25640 277 28650 293 30663 323 33680 355 373100 385 403125 461 –S=Stroke3 position: A + 2 x S4 position: A + S1 + S206.0566www.parker.com/euro_pneumatic
P1DSensorsNew drop-in sensorsThe completely new ”drop-in” P1D sensors can easily beinstalled from the side in the sensor groove, at any positionalong the piston stroke. The sensors are completely recessedand thus mechanically protected. Choose between electronicor reed sensors and several cable lengths and 8 mm andM12 connectors. The same standard sensors are used for allP1D versions, i.e. even for P1D Clean with the patent appliedsystem of integrated sensors. Please note that the sensorswith 8 mm and M12 connector should have cable lengths 1m for P1D Clean to allow flexible positioning of the sensors,including longer stroke lengths. There is a double jointedadapter for the tie-rod version, which offers simple and flexibleuse of standard sensors.Electronic sensorsThe new electronic sensors are ”Solid State”, i.e. they have nomoving parts at all. They are provided with short-circuit protectionand transient protection as standard. The built-in electronicsmake the sensors suitable for applications with high onand off switching frequency, and where very long service life isrequired.Reed sensorsThe sensors are based on proven reed switches, which offerreliable function in many applications. Simple installation, aprotected position on the cylinder and clear LED indication areimportant advantages of this range of sensors.Technical dataDesignGMR (Giant Magnetic Resistance)magneto-resistive functionInstallationFrom side, down into the sensorgroove, so-called drop-inOutputsPNP, normally open (also available inNPN design, normally closed,on request)Voltage range10-30 VDC10-18 V DC, ATEX sensorRipple max 10%Voltage dropmax 2,5 VLoad currentmax 100 mAInternal consumption max 10 mAActuating distancemin 9 mmHysteresismax 1,5 mmRepeatability accuracy max 0,2 mmOn/off switching frequency max 5 kHzOn switching timemax 2 msOff switching timemax 2 msEncapsulation IP 67 (EN 60529)Temperature range –25 °C to +75 °C–20 °C to +45 °C, ATEX sensorIndicationLED, yellowMaterial housing PA 12Material screwStainless steelCable PVC or PUR 3x0.25 mm 2see order code respectivelyTechnical dataDesignReed elementMountingFrom side, down into the sensorgroove, so-called drop-inOutputNormally open , or normally closedVoltage range10-30 V AC/DC or10-120 V AC/DC24-230 V AC/DCLoad currentmax 500 mA for 10-30 V ormax 100 mA for 10-120 Vmax 30 mA for 24-230 VBreaking power (resistive) max 6 W/VAActuating distancemin 9 mmHysteresismax 1,5 mmRepeatability accuracy 0,2 mmOn/off switching frequency max 400 HzOn switching timemax 1,5 msOff switching timemax 0,5 msEncapsulation IP 67 (EN 60529)Temperature range –25 °C to +75 °CIndicationLED, yellowMaterial housingPA12Material screwStainless steelCable PVC or PUR 3x0.14 mm 2see order code respectively6706.05www.parker.com/euro_pneumatic