Pneumatic cylinders - Duncan Rogers

More documents

Recommendations

Info

P1DSensors<strong>Pneumatic</strong> cylinder sensor for P1D-TAn ideal solution where a direct pneumatic signal is wantedfrom a cylinder sensor to a pneumatic control system, forexample. This could be a machine or device in which onlycompressed air is available, and an electricity supply to normalcylinder sensors would involve serious problems or considerableexpense.Function:Non-contacting sensing of a pneumatic cylinder, triggering anoutput signal (conn. 2) from the integrated 3/2 NC valve, whichis activated by a magnetic field or iron core and has a returnspring.If more than one sensor is used with a cylinder there must bea distance of at least 20 mm between sensors to prevent theminfluencing each other.To avoid interference, there must be a minimum spacing of15 mm to steel details.The outlet (conn. 3) must not be blocked or restricted as thiscan impair the function of the sensor.The sensor is fastened to the cylinder using the specialsensor fixing.Technical data:Working pressure: min 2 to max 6 barTemperature: -15 to +60 °CAir quality:3.4.3 to ISO 8573-1 (must be oil free)Function:3/2 NC valveFlow:40 Nl per minuteConnection:for plastic pipe with 3 mm internaldiameterActivation distance: for magnet: min 9 mmActivation distance: for Fe: approx. 2 mmRepetition accuracy: +/- 0.2 mmCylinder velocity: max 1 m/s (depends on magnetic field,interference from steel in environment,signal length requirement from controlsystem….)Distance between sensors: min 20 mmDistance from sensorto steel details:min 15 mmFixing:with sensor fixing or with an M4 thread incaseSensing:non-contacting (also through a wall ofnon-magnetic material)Order codesNameWeight Order codekg<strong>Pneumatic</strong> sensor 0,02 P8S-A34XCylinder fixing 0,01 P8S-AMA13217206.05www.parker.com/euro_pneumatic
P1DSensorsDimensionsActive surface forsensing iron coreIndication40,33,534M49,3212841,214,5 1,616,71821,33,99,114,318,215 1517Cylinder fixing7306.05www.parker.com/euro_pneumatic
Page 1 and 2:
Pneumatic cylindersSeries P1DAccord
Page 3 and 4:
P1DCylinderContentspageISO cylinder
Page 5 and 6:
P1DCylinderThe same high technology
Page 7 and 8:
P1DCylinderComplete accessory progr
Page 9 and 10:
P1DCylinderCushioning screw with po
Page 11 and 12:
P1DCylinderStraight or elbow push-i
Page 13 and 14:
P1DCylinderDesign variants for P1D
Page 15 and 16:
P1DCylinderDesign variants for P1D
Page 17 and 18:
P1DCylinderCylinder forces, double
Page 19 and 20:
P1DMaterial specificationStandard d
Page 21: P1DExample 1 : Which tube diameter
Page 24 and 25: P1DCylinderSafety instructions for
Page 26 and 27: P1DStandard cylinderP1D StandardCAD
Page 28 and 29: P1DThe simple and complete order ke
Page 30 and 31: P1DCylinderP1D cylinders with pisto
Page 32 and 33: P1DCylinderFactory-fitted sensorsAl
Page 34 and 35: P1DCylinderExtended piston rodAll c
Page 36 and 37: P1DCylinderThrough piston rodAll P1
Page 38 and 39: P1DP1D Clean with built-in sensorTh
Page 40 and 41: P1DCylinderP1D CleanThe order numbe
Page 42 and 43: P1DCylinderP1D Flexible PortingThe
Page 44 and 45: P1DCylinderCombine P1D Clean and P1
Page 46 and 47: P1DTechnical dataWorking pressurema
Page 48 and 49: P1DPiston rod lockingP1D-LP1D-DP1D
Page 50 and 51: P1DFastening in positionPiston rod
Page 52 and 53: P1DRod Guidance ModulesAluminium bo
Page 54 and 55: P1DRod Guidance ModulesL1 + SA1B1B4
Page 56 and 57: IP1DMountingsCylinder mountingsType
Page 58 and 59: P1DMountingsCylinder mountingsType
Page 60 and 61: P1DMountingsCylinder mountingsType
Page 62 and 63: P1DMountingsPiston rod mountingsTyp
Page 64 and 65: P1DMountingsCombinationsType Descri
Page 66 and 67: P1DMountingsCombinationsType and de
Page 68 and 69: P1DSensorsElectronic sensorsReed se
Page 70 and 71: P1DSensorsConnecting cables with on
Page 74 and 75: P1DSeal kitsP1D Seal kitsComplete s
Page 76 and 77: P1DSpare PartsOrder key, spare part
Page 78 and 79: P1DOrder code keyThere is a P1D cyl
Page 80 and 81: P1DOrder code keyCylinder versionS
Page 82: P1DOrder code keyInformation notes1
show all

Pneumatic cylinders - Duncan Rogers

Create successful ePaper yourself

Delete template?

Save as template?