NEW - Sobel.rs

Emergency Light Power Supply UnitSeries N 12...Application:As power supply for light fittings with upto 200W which are installed separatelyfrom the "N"-device in a different room.It is especially recommended in cases inwhich the existing environmental conditionsprohibit the use of fittings with selfcontainedbattery sets.Mechanical design:Housing: Polycarbonate, grey (RAL9006), cover screwed to the housing.Battery and electronic device:Each in a separate housing acc. to DINEN 50272-2. Battery compartment withaeration openingMounting: Direct wall mounting (boringsof Ø 6,0mm)Installation: Plug-type terminals (up to2,5mm 2 )Admissible ambient temperature:-5°C up to +35°CInsulation class: IAttention: Installation of this power supply unit is allowedoutside the hazardous area only. Distance betweenthe light fitting and the "N" unit: 500mmax.Voltage drop to be considered acc. to VDE 0100.Wiring diagrams for electronic ballast types:Electrical design:Emergency power supply unit with batteryfor operating 1 or 2 fluorescent lightfittings with electronic ballast (EVG).Emergency light electronic device withdeep discharge protection and switchoversystem for mains/emergency operation.Automatical monitoring acc. toEN 62034. The consumer loads will bemonitored by a self- adjusting performancecontrol device. Manual actuationof the functional tests and display ofmessages and malfunctions via a combinedfoil touch screen.Interface for remote controlling the operatingstate via external switch. Interfacefor malfunction indication.Battery set: With maintenance-free leadbatteryClose-down connectionModes of operation:Maintained or stand-by operationMaintained operation: Switching to batteryoperation in case of mains failure.Stand-by operation: Emergency lampswitches on in case of mains failure only.Rated voltage: 230V / 50HzSuitable for:Light fittings for fluorescent tubes withEVG: For double lamp fittings with doubleEVG, please consider double consumptionor use fittings with 2 EVG(separating the systems)Note:The EVG in the light fittings connectedto the power supply unit must be suitablefor DC and AC operation.Light fittings for incandescent lamps.Admissible consumption acc. to the admissibleconsumption of the fluorescenttubes.mainsunswitchedmainsswitchedligh fittingsoutput interfacecontrol inputstand byN12/... 18AhN12/... 45AhN 12...with separate housing each for the inverter and for the battery setfor light fittings with electronic ballastIP54inverterIP32batterie setType Article no. Lamps/ Flux factor WeightW approx.% 1) appr. kg 2N12/118-58/12/1 DC 12000 0050 1 x 18 – 58 W 1 100 7,1N12/218-36/18/1 DC 12000 0051 2 x 18 – 36 W 1 100 8,8N12/258/24/1 DC 12000 0052 2 x 58 W 1 100 12,8N12/118-58/45/3 DC 12000 0053 1 x 18 – 58 W 3 100 19,2N12/218-36/45/3 DC 12000 0054 2 x 18 – 36 W 3 100 19,2N12/258/90/3 DC 12000 0055 2 x 58 W 3 100 35,51) Ratio effective flux/rated lamp flux 2) Weights without packing materialN12/... 12/24AhN12/... 90AhBitte Subject beachten to technical Sie die changes, Hinweise im misprints Technischen and Anhang! errors.Technische Änderungen, Druckfehler und Irrtümer vorbehalten.280