Spectrum Steam Sound User Guide(1.4MB) - Bachmann

More documents

Recommendations

Info

Miscellaneous FeaturesTranspondingIf you are using Tsunami on a layout equipped with Digitrax transpondingblock detection, you will need to configure Tsunami for transponding-friendlyoperation. Be aware that the Tsunami itself does not transpond - you willneed to install an external transponding decoder in your locomotive toachieve this functionality.Simply program CV 62 to 1 to configure Tsunami for compatibility withexternal transponding devices. To disable transponding compatibility (defaultmode), program CV 62 to 0.Note: Power to the decoder must be cycled before any changes to this CVwill take effect.OEM Steam Sound User’s Guide Page 53Return to Main User's GuideReturn to Table of Contents
TroubleshootingTroubleshootingIf you should have any difficulties with the operation of your Tsunami DigitalSound Decoder, first check this section for hints on trouble shooting. Wehave found that most problems are caused by an errant CV value and areeasily corrected. When all else fails, try resetting the CV values back to theirdefaults (see the section ‘Basic Programming’) and try again.Locomotive doesn’t run but was workingAddress has been accidentally changed.Consist address (CV 19) was accidentally set.CV 29 has been changed to select other address.Acceleration and braking CVs set to very high values.Broken motor wire or track pickup wire.Locomotive never ranSee all the above.Decoder wired incorrectly.Locomotive runs but makes no soundMute function (F8) is on.Another function is re-mapped to the Mute function.Sound Volume CVs have been set to zero.Speaker wire is broken.Speaker is burned out.Locomotive runs in a consist but lights and sound effects don’t workConsist functions are disabled. Set CV 21 and 22 to activate desiredfunctions (see Step 4, ‘Configuring for Consist Operation’).Lights flicker on and offDecoder is in 14 speed step mode and command station is set to 28speed steps.Lights do not workDecoder is in 28/128 speed step mode and command station is setto 14 speed steps.Function mapping is improperly set.Burned out light bulbs.If using 1.5 volt micro-bulbs, resistor value is too large.Broken lamp wires.Tip: Check the decoder’s Diagnostic Codes to confirm that thedecoder is responding to the headlight command when locomotive isgoing forward.Locomotive just sits and flashes both headlights.See next section, ‘Diagnostic Codes’.OEM Steam Sound User’s Guide Page 54Return to Main User's GuideReturn to Table of Contents
Page 1 and 2:
Tsunami ® Digital Sound DecoderSpe
Page 3 and 4:
Table of ContentsAll Aboard! ......
Page 5 and 6: OperationUsing Your Tsunami Digital
Page 7 and 8: OperationJohnson BarChanging the lo
Page 9 and 10: Basics of Programmingare only two b
Page 11 and 12: Basics of Programmingmotor shaft wh
Page 13 and 14: Basics of ProgrammingIt is a good i
Page 15 and 16: Basic ProgrammingStep 1: Configurin
Page 21 and 22: Basic ProgrammingThe exact throttle
Page 25 and 26: Basic ProgrammingEngine 4088.This i
Page 27 and 28: Basic ProgrammingAn output can be a
Page 29 and 30: Basic Programmingwarning beacon fou
Page 31 and 32: Basic ProgrammingTable G. Hyperligh
Page 33 and 34: Sound ProgrammingCV 128, Master Vol
Page 35 and 36: Sound ProgrammingBell ControlBy def
Page 37 and 38: Sound Programmingthrottle settings,
Page 39 and 40: Advanced ProgrammingStep 8: Configu
Page 41 and 42: Advanced Programmingresponse to a l
Page 43 and 44: Advanced Programmingvolume increase
Page 45 and 46: Advanced Programming4. Once you hav
Page 47 and 48: Advanced ProgrammingStrategy for CV
Page 49 and 50: Advanced Programming100%25590%22580
Page 51 and 52: Miscellaneous Featuresyour train sl
Page 53 and 54: Miscellaneous FeaturesA CV setting
Page 55: Miscellaneous FeaturesNote that whe
Page 59 and 60: Troubleshootingrating.Error 16 - CV
Page 61 and 62: Appendix BList of Configuration Var
Page 63: ©2005-2006 Throttle Up! Corp.All R
show all

Spectrum Steam Sound User Guide(1.4MB) - Bachmann

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?