BoosterpaQÂ®- Hydro MPC

More documents

Recommendations

Info

8. Control panelThe control panel in the front cover of the control cabinet featuresa display, a number of buttons and two indicator lights. Thecontrol panel enables manual setting and monitoring of theperformance of the Hydro MPC.8.1 Display (pos. 1)ABCU 3511Fig. 6 Control panelKeyPos. Description1312235467891011TM03 1304 1705DFig. 7Display design8.1.1 Menu lineThe menu line (A) is illustrated in fig. 7.The display has four main menus:CTM04 6191 50091 Display2 Arrow to the right3 Help4 Up5 Down6 Plus7 Minus8 Esc9 Home10 Ok11 Indicator light, operation (green)12 Indicator light, alarm (red)13 ContrastStatus:Operation:Alarm:Settings:Indication of system statusChange of operating parameters such as setpoint(password option)Alarm log for fault findingChange of settings (password option)8.1.2 Top lineThe top line (B) is illustrated in fig. 7.The top line shows• the display number and title (left side)• the selected menu (left side)• the symbol in case of alarm (right side)• the symbol if the service language has been selected (rightside).8.1.3 Graphical illustrationThe graphical illustration (D) may show a status, an indication orother elements, depending on the position in the menu structure.The illustration may show the entire system or part of it as well asvarious settings.8.1.4 Scroll barIf the list of illustration elements exceeds the display, the symbolsand will appear in the scroll bar to the right. Use theand buttons to move up and down in the list.8.1.5 Bottom lineThe bottom line (C) shows the date and time.14
8.2 Buttons and indicator lightsThe buttons (pos. 2 to 10 in fig. 6) on the CU 351 are active whenthey are illuminated.8.2.1 Arrow to the right (pos. 2)Press the button to move to the next menu in the menustructure. If you press when the Settings menu ishighlighted, you go to the Status menu.8.2.2 Help (pos. 3)When the button is illuminated, a help text applying to thecurrent display will appear if the button is pressed.Close the text by pressing the button.8.2.3 Up and down (pos. 4 and 5)Press the and buttons to move up and down in lists.A text can be selected when it is in a box.If a text is marked and the button is pressed, the text abovewill be marked instead. If the button is pressed, the textbelow will be marked.If the button is pressed in the last line in the list, the first linewill be marked.If the button is pressed in the first line in the list, the last linewill be marked.8.2.4 Plus and minus (pos. 6 and 7)Use the and buttons to increase and reduce values.A value is activated when the button is pressed.8.2.5 Esc (pos. 8)Use the button to go one display back in the menu.If a value has been changed and the button is pressed, thenew value will not be saved. For further information, see section8.2.7 Ok (pos. 10).If the button is pressed before the button, the new valuewill be saved. For further information, see section 8.2.7 Ok (pos.10).8.2.6 Home (pos. 9)Press the button to return to the Status menu.8.2.7 Ok (pos. 10)Use the button as an enter button.The button is also used to start the setting of a value.If a value has been changed and the button is pressed, thenew value will be activated.8.2.8 Indicator lights (pos. 11 and 12)The Hydro MPC control panel incorporates a green and redindicator light.The green indicator light is on when the Hydro MPC is inoperation.It is flashing if the Hydro MPC has been set to stop.The red indicator light is on if there is an alarm or a warning. Thefault can be identified from the alarm list.8.2.9 Contrast (pos. 13)The contrast in the display can be changed by means of thebutton:1. Press .2. Adjust the contrast with and .8.2.10 Back lightIf no button is touched for 15 minutes, the back light of the panelwill be dimmed, and the first display in the Status menu willappear.Press any button to re-activate the back light.15
Page 1: GRUNDFOS INSTRUCTIONSBoosterpaQ ®
Page 5 and 6: CONTENTSPage1. Symbols used in this
Page 7 and 8: 4. NameplateThe nameplate of the bo
Page 9 and 10: 6.1 Examples of control variantsSys
Page 11 and 12: 7. InstallationBefore installation
Page 13: INSTALLATION AND STARTUP NOTES13
Page 17 and 18: Continued from page 164. Settings4.
Page 19 and 20: 9.2 OverviewSection Display and dis
Page 21 and 22: 9.3 Description of functionsThe des
Page 23 and 24: Finally the resulting current setpo
Page 25 and 26: 9.5.3 Control mode (2.1.2)Open loop
Page 27 and 28: 26.Select the required number of po
Page 29 and 30: 9.6 Alarm (3)The Alarm menu gives a
Page 31 and 32: MPC alarm indication"Protocol descr
Page 33 and 34: MPC alarm indication"Protocol descr
Page 35 and 36: 9.7.1 Primary controller (4.1)Fig.
Page 37 and 38: 17.Mark Activated with or , and pre
Page 40 and 41: In this menu section, it is possibl
Page 43 and 44: 9.7.19 Pump start and stop speed (4
Page 45 and 46: When the stop function is activated
Page 47 and 48: 2. Pressure build-up phase.The syst
Page 49 and 50: Setting via control panel1. Mark th
Page 51 and 52: 9.7.32 Functions of digital outputs
Page 53 and 54: 9.7.37 Pump curve data (4.3.19)Duty
Page 55 and 56: At large flow rates, there may be a
Page 57 and 58: 9.7.45 Dry-running protection with
Page 59 and 60: 9.7.49 Limit 1 and 2 exceeded (4.4.
Page 61 and 62: 9.7.52 Functions, CU 351 (4.5)Fig.
Page 63 and 64: 9.7.56 Passwords (4.5.4)Description
Page 65 and 66:
9.8 Data communicationCU 351 is equ
Page 67 and 68:
Change of passwordTM03 2051 3505Fig
Page 69 and 70:
10.2 VLT FC 202Press [EXTEND MENU]
Page 71 and 72:
11. Fault finding chartWarningBefor
Page 73:
15.2 TemperatureLiquid temperature:
Page 76:
Being responsible is our foundation
show all

BoosterpaQÂ®- Hydro MPC

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?