BoosterpaQ®- Hydro MPC

9.2 OverviewSection Display and display number See page9.4 Status (1) 219.4.1 Current alarms (3.1) 219.4.2 System (1.2) 219.4.3 Operating mode (1.2.1) 229.4.4 Setpoint (1.2.2) 229.4.5 Setpoint influence (1.2.3) 229.4.6 Measured values (1.2.4) 239.4.7 Analog inputs (1.2.5) 239.4.8 Pump 1...6 (1.3 to 1.8) 239.5 Operation (2) 239.5.1 Operation (2) 249.5.2 System operating mode (2.1.1) 249.5.3 Control mode (2.1.2) 259.5.4 Setpoints (2.1.3) 279.5.5 Individual pump control (2.1.4) 279.5.6 Setting of individual operating mode (2.1.4.1 to 2.1.4.6) 289.6 Alarm (3) 299.6.1 Alarm status (3) 299.6.2 Current alarms (3.1) 349.6.3 Alarm log (3.2) 349.7 Settings (4) 349.7.1 Primary controller (4.1) 359.7.2 PI controller (4.1.1) 359.7.3 Alternative setpoints (4.1.2) 359.7.4 Alternative setpoints 2 to 7 (4.1.2.1 to 4.1.2.7) 369.7.5 External setpoint influence (4.1.3) 369.7.6 Setting of influence function (4.1.3.2) 379.7.7 Primary sensor (4.1.4) 379.7.8 Clock program (4.1.6) 389.7.9 Proportional pressure (4.1.7) 389.7.10 S-system configuration (4.1.8) 399.7.11 Pump cascade control (4.2) 399.7.12 Min. time between start/stop (4.2.1) 409.7.13 Max. number of starts/hour (4.2.1) 409.7.14 Standby pumps (4.2.3) 419.7.15 Forced pump changeover (4.2.4) 419.7.16 Pump test run (4.2.5) 419.7.17 Pilot pump (4.2.6) 429.7.18 Pump stop attempt (4.2.7) 429.7.19 Pump start and stop speed (4.2.8) 439.7.20 Min. performance (4.2.9) 439.7.21 Compensation for pump start-up time (4.2.10) 449.7.22 Secondary functions (4.3) 449.7.23 Stop function (4.3.1) 449.7.24 Soft pressure build-up (4.3.3) 469.7.25 Emergency run (4.3.5) 479.7.26 Digital inputs (4.3.7) 489.7.27 Functions of digital inputs (4.3.7.1) 489.7.28 Analog inputs (4.3.8) 499.7.29 Analog inputs (4.3.8.1 to 4.3.8.7) 499.7.30 Analog inputs and measured value (4.3.8.1.1 to 4.3.8.7.1) 509.7.31 Digital outputs (4.3.9) 509.7.32 Functions of digital outputs (4.3.9.1 to 4.3.9.16) 519.7.33 Min., max. and user-defined duty (4.3.14) 519.7.34 Min. duty (4.3.14.1) 5119