GP1670F_1870F Operator's Manual - Furuno USA

More documents

Recommendations

Info

13. INSTALLATION13.3.3 How to mount a transducer inside the hullThe transducer may also be installed inside the hull on FRP boats. However, this installationmethod affects the ability to detect the bottom, fish and other objects becausethe ultrasound pulse is weakened when it passes through the hull.Note: This mounting method should not be used to mount the transducer that supportsthe ACCU-FISH TM and/or bottom discrimination display feature, since performanceis greatly degraded.Necessary toolsThe following tools are required:• Sandpaper (#100)• Silicone sealantRemarks on installation• Do the installation with the ship moored at a dock, etc. The water depth should be 6.5-32 feet (2-10 meters).• Turn off the engine.• Do not power the unit with the transducer in the air, to prevent damage to the transducer.• Do not use this method on a double layer hull.• Before attaching the transducer to the hull, check that the site is suitable. Put thetransducer in a water-filled plastic bag. Connect the transducer to the display unit andput the transducer on the installation site. Turn on the display unit and check that thedepth indication appears.Installation procedureThe attenuation of the ultrasound pulse varies with the thickness of the hull. Select alocation where attenuation is the lowest.1. Select 2-3 locations considering the four points mentioned below. (You will finalizethe mounting location through some trial and error later.)• Mount the transducer at a location 1/2 to 1/3 of the length of your boat from thestern.• The mounting location is between 15 to 50 cm from the centerline of the hull.• Do not place the transducer over hull struts or ribs which run under the hull.• Avoid a location where the rising angle of the hull exceeds 15°, to minimize theeffect of the boat's rolling.Centerline50 cm50 cm1/215 cm15 cm1/3Transducermountinglocation2. Clean the face of the transducer to remove any foreign material. Lightly roughenthe face with #100 sandpaper. Also, use the sandpaper to roughen the inside ofthe hull where the transducer is to be mounted.13-6
13. INSTALLATION3. Wipe off any sandpaper dust from the face of the transducer.4. Dry the face of the transducer and the hull. Coat the transducer face and mountinglocation with silicone sealant. Hardening begins in approx. 15-20 minutes so dothis step without delay.TransducerSiliconeSealant5. Attach the transducer to the hull.Press the transducer firmly down on the hulland gently twist it back and forth to removeany air which may be trapped in the siliconesealant.6. Support the transducer with a piece of woodto keep it in place while the sealant is drying.It takes 24-72 hours to harden completely.HullSiliconeSealant13.3.4 TriducerDO NOT overtighten screws, to prevent damage to the transducer.525STID-MSDThe optional triducer 525STID-MSD is designed for thru-hull mounting.ø79BOW133 2.00"-12 UNthreadsø51 727 140 Unit: mm525STID-PWDThe optional transom mount triducer 525STID-PWD can be installed by the thru-hullmethod or the inside-hull method.13-7
Page 1 and 2:
GPS PLOTTER/SOUNDERModelGP-1670F/GP
Page 3 and 4:
IMPORTANT NOTICESGeneral• This ma
Page 5 and 6:
SAFETY INSTRUCTIONSCAUTIONDo no tur
Page 7 and 8:
TABLE OF CONTENTS3.2.3 How to enter
Page 9 and 10:
TABLE OF CONTENTS9. MEMORY CARD OPE
Page 11 and 12:
FOREWORDA Word to GP-1670F, GP-1870
Page 13 and 14:
SYSTEM CONFIGURATIONThe environment
Page 15 and 16:
EQUIPMENT LISTSName Type Code no. R
Page 17 and 18:
1. OPERATIONAL OVERVIEW1.1 Controls
Page 19 and 20:
1. OPERATIONAL OVERVIEWTested SD ca
Page 21 and 22:
1. OPERATIONAL OVERVIEW1.2 RotoKey
Page 23 and 24:
1. OPERATIONAL OVERVIEW2D plotter d
Page 25 and 26:
1. OPERATIONAL OVERVIEW1.6 The Curs
Page 27 and 28:
1.8 Home Screen (Display Selection)
Page 29 and 30:
1. OPERATIONAL OVERVIEW5. Select a
Page 31 and 32:
1. OPERATIONAL OVERVIEWWind meter+n
Page 33 and 34:
1. OPERATIONAL OVERVIEWHow to selec
Page 35 and 36:
1. OPERATIONAL OVERVIEWAuto course-
Page 37 and 38:
1. OPERATIONAL OVERVIEW4) Press the
Page 39 and 40:
1. OPERATIONAL OVERVIEWItem Context
Page 41 and 42:
1. OPERATIONAL OVERVIEW1.17 Tide In
Page 43 and 44:
2. TRACKYour boat’s track is plot
Page 45 and 46:
2.7 How to Delete Track by Color2.
Page 47 and 48:
3. POINTS3.1 What is a Point?In nav
Page 49 and 50:
3. POINTS[Hide]: Hide the icon and
Page 51 and 52:
3. POINTS3.5 How to Select Visibili
Page 53 and 54:
4. ROUTES4.1 What is a Route?Often
Page 55 and 56:
4. ROUTES5) After you have entered
Page 57 and 58:
4. ROUTES4. Select [EASY ROUTING] f
Page 59 and 60:
4. ROUTES4.4 How to Insert a Point
Page 61 and 62:
4. ROUTES4.7.2 Functions available
Page 63 and 64:
4. ROUTES4.9 How to Display a Route
Page 65 and 66:
5. NAVIGATIONThis chapter shows you
Page 67 and 68:
5. NAVIGATION• A red line runs be
Page 69 and 70:
6. MAP SETTINGS, 2D PERSPEC-TIVE/3D
Page 71 and 72:
6. MAP SETTINGS, 2D PERSPECTIVE/3D
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
7. FISH FINDER OPERATIONS7.1 How th
Page 79 and 80:
7.3 How to Activate the Fish Finder
Page 81 and 82:
7. FISH FINDER OPERATIONSMarker zoo
Page 83 and 84:
7. FISH FINDER OPERATIONS• The 60
Page 85 and 86:
7.6 Manual Fish Finder Operation7.
Page 87 and 88:
7. FISH FINDER OPERATIONSClutter7.7
Page 89 and 90: 7. FISH FINDER OPERATIONS7.10 How t
Page 91 and 92: 7.14.1 How to set an alarm7. FISH F
Page 93 and 94: 7. FISH FINDER OPERATIONS7.15.2 How
Page 95 and 96: 7.17 FISH FINDER Menu7. FISH FINDER
Page 97 and 98: 7. FISH FINDER OPERATIONSItem[50 kH
Page 99 and 100: 7. FISH FINDER OPERATIONSBottom con
Page 101 and 102: 7. FISH FINDER OPERATIONSPlanktonA
Page 103 and 104: 8. ALARMSThe plotter section has 11
Page 105 and 106: 8. ALARMS8.4 XTE AlarmThe XTE (cros
Page 107 and 108: 8. ALARMS8.8 Anchor AlarmThe anchor
Page 109 and 110: 9. MEMORY CARD OPERATIONSThis syste
Page 111 and 112: 9.6 How to Delete Files from an SD
Page 113 and 114: 9. MEMORY CARD OPERATIONS9.8.3 How
Page 115 and 116: 10. OTHER FUNCTIONS10.1 AIS Operati
Page 117 and 118: 10.2 DSC Message Information10. OTH
Page 119 and 120: 10. OTHER FUNCTIONS10.4 How to Sele
Page 121 and 122: 10. OTHER FUNCTIONS10.5 Engine Disp
Page 123 and 124: 11. CUSTOMIZING YOUR UNITThe defaul
Page 125 and 126: 11. CUSTOMIZING YOUR UNIT11.3 SYSTE
Page 127 and 128: 11. CUSTOMIZING YOUR UNIT[RESTART G
Page 129 and 130: 12. MAINTENANCE,TROUBLESHOOTINGThis
Page 131 and 132: 12. MAINTENANCE, TROUBLESHOOTINGPro
Page 133 and 134: 12. MAINTENANCE, TROUBLESHOOTING12.
Page 135 and 136: 13. INSTALLATION13.1 Installation o
Page 137 and 138: 13. INSTALLATIONin a position where
Page 139: 13.3.2 Transom mount transducer13.
Page 143 and 144: 13. INSTALLATIONHow to install the
Page 145 and 146: 13. INSTALLATIONHow to attach the s
Page 147 and 148: 13. INSTALLATION8. Launch your boat
Page 149 and 150: 13.5 Wiring13. INSTALLATIONAll wiri
Page 151 and 152: 13. INSTALLATIONHow to extend cable
Page 153 and 154: 13. INSTALLATION13.6 Initial Settin
Page 155 and 156: 13. INSTALLATION13.6.2 CAN bus inpu
Page 157 and 158: 13. INSTALLATIONPGNDescription12748
Page 159 and 160: APPENDIX 1 MENU TREEESC/MENU(long p
Page 161 and 162: APPENDIX 1 MENU TREE11(Con’t from
Page 163 and 164: APPENDIX 1 MENU TREE1(Con’t from
Page 165 and 166: APPENDIX 2 ABBREVIATIONS, SYMBOLSAb
Page 167 and 168: APPENDIX 2 ABBREVIATIONS, SYMBOLSSy
Page 169 and 170: APPENDIX 3 JIS CABLE GUIDECables li
Page 171 and 172: FURUNOGP-1670F/1870FSPECIFICATIONS
Page 173 and 174: PACKING LIST GP-1670F-E 14CW-X-9852
Page 175 and 176: D-1
Page 177 and 178: D-3
Page 179 and 180: D-5
Page 181 and 182: INDEXNumerics2D perspective dispay.
Page 183 and 184: INDEXrecording interval............
Page 185: FURUNO Warranty for North AmericaFU
show all

GP1670F_1870F Operator's Manual - Furuno USA

Create successful ePaper yourself

Delete template?

Save as template?